Author Topic: configure the D-Link DIR-506L wireless access point- SOLVED  (Read 38932 times)

Rich442

  • Guest
Re: connecting with the D-Link 506L wireless access point
« Reply #15 on: April 04, 2016, 12:03:18 am »
OK, here is the Thinkcentre
Quote
[N:\]ifconfig lan0
lan0: flags=8843<UP,BROADCAST,RUNNING,MULTICAST,LOOPBRD>
        inet 192.168.0.78  netmask 0xffffff00 broadcast 192.168.0.255
Pinging 192.168.0.78
Quote
N:\]ping 192.168.0.255
PING 192.168.0.255: 56 data bytes
64 bytes from 192.168.0.78: icmp_seq=0. time=0. ms
64 bytes from 192.168.0.78: icmp_seq=1. time=0. ms
64 bytes from 192.168.0.78: icmp_seq=2. time=0. ms
64 bytes from 192.168.0.78: icmp_seq=3. time=0. ms
64 bytes from 192.168.0.78: icmp_seq=4. time=0. ms
64 bytes from 192.168.0.78: icmp_seq=5. time=0. ms
64 bytes from 192.168.0.78: icmp_seq=6. time=0. ms

----192.168.0.255 PING Statistics----
7 packets transmitted, 7 packets received, 0% packet loss
round-trip (ms)  min/avg/max = 0/0/0
asking for the netstat:
Quote
[N:\]netstat -r
  destination             router                netmask     metric flags intrf

default                192.168.0.1            0.0.0.0           0   UGP   lan0
127.0.0.1              127.0.0.1              255.255.255.255   0    UH     lo
192.168                192.168.0.78           255.255.255.0     0    UC   lan0

Finally, here is me showing route packets on the way to my Workstation (IBM Thinkcentre)
Quote
[N:\]tracerte 192.168.0.78
traceroute to 192.168.0.78 (192.168.0.78), 30 hops max, 38 byte packets
 1  192.168.0.78              (192.168.0.78)  0 ms  0 ms  0 ms
[N:\]
« Last Edit: April 04, 2016, 12:37:34 am by Richard Crowley »

Neil Waldhauer

  • Hero Member
  • *****
  • Posts: 1073
  • Karma: +27/-0
    • View Profile
    • Blonde Guy
Re: connecting with the D-Link 506L wireless access point
« Reply #16 on: April 04, 2016, 12:16:05 am »
Point your web browser to 192.168.0.1. I hope the admin password is included in the router documentation.

You should get the control panel for the D-Link 506L.
Expert consulting for ArcaOS, OS/2 and eComStation
http://www.blondeguy.com

Doug Bissett

  • Hero Member
  • *****
  • Posts: 1604
  • Karma: +4/-2
    • View Profile
Re: connecting with the D-Link 506L wireless access point
« Reply #17 on: April 04, 2016, 12:56:11 am »
Quote
Point your web browser to 192.168.0.1. I hope the admin password is included in the router documentation.

You should get the control panel for the D-Link 506L.

You may also get your router, depending on which mode the 506l is in.

Rich442

  • Guest
Re: connecting with the D-Link 506L wireless access point
« Reply #18 on: April 04, 2016, 05:09:15 pm »
Point your web browser to 192.168.0.1. I hope the admin password is included in the router documentation.

You should get the control panel for the D-Link 506L.

Indeed, 192.168.0.1 is the d-link control center as is dlinkrouter.local (no www). After going there, it was a matter of clicking Setup-->Internet-->Internet Connection Wizard. What I missed was that the D-Link wanted to be configured as a WiFi hotspot and not as a "DHCP Connection (Dynamic IP Address)." Otherwise, as a

The control panel does not need a password the first time but prompts you to set one while configuring the device.

That seemed to contradict everything I was expecting, because the TCP/IP Configurator in system setup seems to encourage the DHCP method. The connection and the 506L are now running quite well.

For what it's worth, the D-Link documentation states that there are two modes for the 506L: "Wireless Router Mode" (which I was using (with the ethernet cable)) and "Wi-Fi Hotspot Mode" (this what D-Link is calling them).

Thank you all so so much. :)
« Last Edit: April 04, 2016, 11:42:50 pm by Richard Crowley »