Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Floyd

Pages: [1]
Hardware / Re: SATA AHCI weirdness
« on: June 26, 2013, 07:18:27 pm »
I went over everything again and updated it all to the eCS 2.2 Live CD drivers, here's what it's doing now.

in AHCI mode, OS2AHCI and Danis506 seem to work fine, but then it hangs on whatever driver loads immediately after Danis506 (first it was DaniATAPI, I removed that and then it was OS2DASD.DMD) with no error message. I let it sit for 10 minutes before I hit reset to be sure.

in AHCI mode without OS2AHCI it can't operate disk drive.

In IDE mode it boots fully to the desktop and everything seems to work fine (well, no mouse, but I have not installed a USB mouse driver yet). If I try to shut down or restart with ctrl-alt-delete it hangs and I have to hit reset, then it doesn't get any further than chkdsk on the next boot.

I can live in IDE mode if I have to, if anyone has any ideas about why it hangs at shutdown.

Hardware / Re: SATA AHCI weirdness
« on: June 24, 2013, 04:52:14 pm »
according to you need danis 1.8.9 or better to have ahci and danis working together.
I couldn't find a download of that anywhere, but I did try version 1.8.15 from the eCS Live CD and in AHCI mode it was the same old stuff,  but then with the BIOS in IDE mode...

well, at least it found the disks this time.

Hardware / Re: SATA AHCI weirdness
« on: June 24, 2013, 12:17:37 am »
You could try 1.25:

different cat, same result.

os2ahci recognizes my hardware, danis506 loads but doesn't do anything else, and os2acapi does not do anything at all.

Hardware / Re: SATA AHCI weirdness
« on: June 23, 2013, 04:31:15 pm »
I think the only possibility would be to try the /r parameter with it. If that won't work, you probably need the one that comes with eComStation (now at version 1.29, which is very much newer than version 1.4 that is at HOBBES).
I tried /r, it didn't help. This is kind of what I thought would be the problem, I guess I will just have to save up some money and buy the new ecomstation when it finally comes out.  thanks for the help, everyone.

Hardware / Re: SATA AHCI weirdness
« on: June 23, 2013, 03:10:02 am »
Here is some more hardware info:
Motherboard- Intel BOXDH77KC LGA 1155 It does support ACPI.
CPU- Intel i3-2120 3.30Ghz
8gb of RAM
Intel 7 Series/C216 chipset family SATA AHCI controller

I'm just using the on-board video and sound for now, I doubt that would stop it from booting.

Hardware / Re: SATA AHCI weirdness
« on: June 23, 2013, 01:20:36 am »
os2ahci is version 0.1.4 (the one from hobbes). I have tried setting the BIOS to both SATA and IDE mode, with and without os2ahci loaded, I even tried SCSI mode once, to no avail. Danis506 does not seem to recognize the drive no matter what I do, but daniatapi.flt will not load at all. all my hardware *should* be compatible, and like I said, it worked one time from a fat16 partition. I may try that again and see what it does.

Hardware / SATA AHCI weirdness
« on: June 22, 2013, 07:46:00 pm »
Hi, long time lurker, first time poster. I was wondering if anyone might be able to help me out.

Let's start at the beginning. I have been trying to install Warp 4 on my primary desktop computer, I can give more detailed hardware info if you need it. It doesn't have a floppy drive so I installed a really basic version of OS/2 in Virtual PC and then wrote the virtual hard drive image to the physical disk. I added the latest versions of DaniATAPI.flt, and DaniS506.add to the system as well as OS2AHCI.add (not the latest version) before I transferred the image
OS/2 boots up to a point OS2AHCI correctly recognizes the Intel ich7 chipset but then DaniATAPI won't load and it gives the "OS/2 cannot operate your hard disk" error.
I did this with and without Fixpack 15 applied before the transfer and got the same results, the one time I did get it to work was from a FAT partition instead of HPFS, but it corrupted the desktop as soon as it was shut down.

I have done all I know to do, I don't really have the money to spend on a copy of eCS right now, though the Live CD does work great. I stared this just for something to do, but now I am determined to get it to work. I realize that it could be a problem with the image transfer, and if that is it, I guess I'm done, unless it is possible to make a custom boot CD.

Any help anyone can give would be greatly appreciated!

Pages: [1]