Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Igor

Pages: [1] 2 3 ... 5
1
Programming / Re: Building Qt5
« on: November 22, 2022, 03:57:00 pm »
Dear builders Qt5 please turn off the AVX (and AVX2) code. Due to its presence, the browser does not display the pages. And it is impossible to use libraries. I don’t understand why this code is included if it does not work on OS/2 correctly?

2
Hardware / Re: Iomega ZIP 100 IDE
« on: November 13, 2022, 09:53:58 pm »
Solved!

1. Install ZIP100 as a hard drive (not like a floppy disk).
2. Install Danis driver:
BASEDEV=DANIS506.ADD /!BIOS /A:1 /I /V
BASEDEV=DANIATAP.FLT /EJ /V
3. After installing the disk in the wildcard, use the LVM command - lvm /rediscoverprm
4. A disk letter will appear and you can work with it
5. Before extracting the disk, use the command - eject drive:

Thank you all for participating in solving the problem!

3
Applications / Re: Test build of dooble with qt5
« on: May 02, 2022, 03:03:34 pm »
Hi!

Please create an assembly QT5 without support of the ABX. Due to the presence of ABX, an error occurs and the browser falls into the trap.

4
Hardware / Re: WebCam Driver Question
« on: March 27, 2022, 11:35:54 pm »
May be you can give a try recording video+sound using ffmpeg and check if the sound problem exist too !

ffmpeg correctly records video with sound over 2 minutes. This is amazing.

5
Hardware / Re: WebCam Driver Question
« on: March 26, 2022, 10:24:27 pm »
Hi Remy,

What did you before having sound issue ?
Did you try your webcam with all other programs stopped ?
 
(I've got the symptom you describe when audio driver has to handle mutiple sources)
ex: Out of webcam + pm123 or pm123 + youtube or wps playing audio + other audio programs...

Before I got the problem with the sound, I tried several times to start the video server program, because it starts correctly for me only on the third try. And always on the third try.

No other sound programs were active during the test. The only thing I can notice is the system sounds when the camera is connected. However, in this case, I did not disconnect the camera and did not reconnect it. It has been attached before.

6
Hardware / Re: WebCam Driver Question
« on: March 25, 2022, 04:34:23 pm »
Hi Wim,

Thank you. I updated the programs to the version you specified.
The program wmaudio outputs sound from 30 seconds to 1 minute. Then the last fragment is repeated forever. After restarting the program wmaudio, the sound is restored and works for some time. Not more than a minute. The server webcam.exe does not need to be restarted. It works correctly.

7
Hardware / Re: WebCam Driver Question
« on: March 23, 2022, 06:59:41 pm »
Hi Wim,

Thank you for your work. This version earned. The first launch was with a video stream error. The second launch was with an audio stream error - the sound looked at one repeating click to which I tried to check the microphone.

However, from the third launch - everything worked correctly and there is sound. The fourth launch also showed excellent results.
However, the sound disappears after a few minutes of using the camera. Video - continues to work.
To restore audio, a restart of the receiver program (wmaudio) is required.

8
Hardware / Re: WebCam Driver Question
« on: March 23, 2022, 01:29:38 pm »
Hi Wim,

There is an assumption that the program lacks delays. Or the device cannot be immediately connected by the program. Because after initializing the device (after connecting to the connector), it does not work. When restarted, the video works, but the sound also does not connect. I assume that somewhere a waiting cycle is required or a retry of the connection is required.

9
Hardware / Re: WebCam Driver Question
« on: March 23, 2022, 01:21:48 pm »
Hi Wim,

I tested this version.
The first:
Code: [Select]
start webcam /a /n
started.
format:yuyv
 acquire webcam
 set configuration
 negotiate video format
/a server (audio) On-Line.
 obtain video format
 commit video format
 set video alt interface
[0000804C]
obtain video error.
/n server (video) On-Line.
 set audio frequency
 set audio mike volume
[00008040]
obtain audio error.
The second and beyond:
Code: [Select]
start webcam /a /n
started.
format:yuyv
 acquire webcam
 set configuration
 negotiate video format
/a server (audio) On-Line.
 obtain video format
 commit video format
 set video alt interface
/n server (video) On-Line.
 set audio frequency
 starting iso video
 set audio mike volume
[00008040]
obtain audio error.

10
Hardware / Re: WebCam Driver Question
« on: March 22, 2022, 07:45:25 pm »
Hallo Igor,

I think I know now where the problem is. It is in the scanning of the usb descriptors.  Please send me the "lsusb -d 09da:2695 -v" report of your camera.

Wim
Hi Wim,

See attache.

11
Hardware / Re: WebCam Driver Question
« on: March 22, 2022, 03:26:43 pm »
Hi Igor,

Let me try. I have some questions for you to answer first...

1. Are you using ArcaOS or eComStation or what? Which version?
2. Are you using ArcaOS or Lars Erdmann drivers? Which version? 
3. Is this camera the only camera connected to your system?
4. Does your laptop have a builtin camera? Is it enabled in the bios?
5  What version of webcam.exe are you using?

Following Remy's suggestion /dN you select the proper camera to be used.
So "webcam /d09DA:2695:0100 /a" forces to use the proper camera.

Following Remy's suggestion /iN you reduce video bandwidth.
So "webcam /d09DA:2695:0100 /a /i1 uses less video bandwidth.

Wim

Hi Wim,
1. I use ArcaOS 5.0.7
2. ArcaOS drivers 12.11
3. Is this the only camera in USB interface
4. This is desktop computer
5  W.M.Brul:00.20210214
Specify on the command line "/d09DA:2695:0100" leads to this error:
Code: [Select]
started.
format:yuyv
 acquire webcam
 set configuration
 negotiate video format
 obtain video format
 commit video format
 set video alt interface
[0000804C]
obtain video error.

At the same time, the launch of the program with the "webcam /a /n" parameters allows you to view the video from the camera.

12
Hardware / Re: WebCam Driver Question
« on: March 21, 2022, 12:25:43 am »
using pipe video only:
webcam /d09DA:2695:0100/n/i1  !

Video works in default configuration. Audio does not work (microphone).

13
Hardware / Re: WebCam Driver Question
« on: March 20, 2022, 08:29:08 pm »
Hi Wim

Code: [Select]
webcam /a /n
started.
format:yuyv
 acquire webcam
 set configuration
 negotiate video format
 obtain video format
 commit video format
 set video alt interface
/n server (video) On-Line.
 starting iso video

USB Dock: Unknown device
Identifier: 09da:2695

<<< Device Description >>>
Type :01
USB Rev :200
Class : Miscellaneous Device (0xEF)
Subclass : Common Class (0x02)
Protocol : Interface Association (0x01)
Max. packetsize :64
Vendor  ID :0x09DA
Product ID :0x2695
Device Release# :0100
Number of Configurations:1

Configuration: 0
Length : 941
ConfigurationValue : 1
Attributes : 0x80
MaxPower : 0xFA
NumInterfaces : 4
USB_DT_UNKNOWN_FOR_ME

Interface: 0
AlternateSetting : 0
Class : Video (0x0E)
SubClass : Video Control (0x01)
Protocol : Unknown (0x00)
Endpoints : 1
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME

Endpoint: 0
Address : 0x83
Attributes : 0x03 (Irq)
MaxPacketSize : 16
Interval : 6
USB_DT_UNKNOWN_FOR_ME

Interface: 1
AlternateSetting : 0
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 0
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME

Interface: 1
AlternateSetting : 1
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1

Endpoint: 0
Address : 0x81
Attributes : 0x05 (Iso)
MaxPacketSize : 128
Interval : 1

Interface: 1
AlternateSetting : 2
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1

Endpoint: 0
Address : 0x81
Attributes : 0x05 (Iso)
MaxPacketSize : 256
Interval : 1

Interface: 1
AlternateSetting : 3
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1

Endpoint: 0
Address : 0x81
Attributes : 0x05 (Iso)
MaxPacketSize : 800
Interval : 1

Interface: 1
AlternateSetting : 4
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1

Endpoint: 0
Address : 0x81
Attributes : 0x05 (Iso)
MaxPacketSize : 2848
Interval : 1

Interface: 1
AlternateSetting : 5
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1

Endpoint: 0
Address : 0x81
Attributes : 0x05 (Iso)
MaxPacketSize : 4896
Interval : 1

Interface: 1
AlternateSetting : 6
Class : Video (0x0E)
SubClass : Video Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1

Endpoint: 0
Address : 0x81
Attributes : 0x05 (Iso)
MaxPacketSize : 5120
Interval : 1
USB_DT_UNKNOWN_FOR_ME

Interface: 2
AlternateSetting : 0
Class : Audio (0x01)
SubClass : Control Device (0x01)
Protocol : Unknown (0x00)
Endpoints : 0
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME

Interface: 3
AlternateSetting : 0
Class : Audio (0x01)
SubClass : Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 0

Interface: 3
AlternateSetting : 1
Class : Audio (0x01)
SubClass : Streaming (0x02)
Protocol : Unknown (0x00)
Endpoints : 1
USB_DT_UNKNOWN_FOR_ME
USB_DT_UNKNOWN_FOR_ME

Endpoint: 0
Address : 0x84
Attributes : 0x05 (Iso)
MaxPacketSize : 192
Interval : 4
USB_DT_UNKNOWN_FOR_ME

I do not work with the sound from the camera. Could you help with this?

14
Off Topic discussions / Re: Russia attacked Ukraine
« on: February 25, 2022, 12:04:05 pm »

I was tempted to contact of our Russian community friends just know like "a  man in the street" point of view, but I was advice not to do that to protect themself in case they are not in favor of the Russian government.

Russia is not know for their freedom of speech on these days, communications may be monitored, and it is better not to put them in trouble.
In Russia, military censorship will be introduced. Participants of anti-war rallies are delayed and imprisoned.

Nevertheless, I urge to take care of the Ukrainians because they have a chance to die.

No war!

15
Off Topic discussions / Re: Russia attacked Ukraine
« on: February 24, 2022, 08:47:29 pm »
To my great regret, Russia began this war. I sincerely wish the courage to the inhabitants of Ukraine and want the world rather came.
Os4user take care of yourself. I hope that everything will be alright.

Pages: [1] 2 3 ... 5