Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - roberto

Pages: 1 ... 50 51 [52] 53 54
766
Hardware / Re: Which buy a new laptop? for 2016
« on: January 26, 2016, 08:29:53 pm »


Quote

I hope you mean E1000E. You should also try the E1000B driver. I find that it works better, and it will be the one that will be developed in the future.
Thanks

Quote
   
NETBIOS is not supported with that PROTOCOL.INI. You will have errors at boot, if you don't REM the lines for it. However, all you need to do is hit enter to get by them. The objective now is to get the driver for the WiFi to load, with a minimum configuration, to see if it actually loads, or not. If you see green and white information, it probably loads okay. If it doesn't, more information is probably needed to make sure I picked the proper driver (I only guessed). If that part looks okay, you need to try XWLAN to see if it will start the radio (I expect that that part isn't going to work). If that does work, then you can add any other drivers, and put the NETBIOS over TCPIP back in. If it doesn't work, I don't know of any way to get around that, other than to wait for the WiFi driver that Arca Noae is working on.


Many thanks again, I need more time. We return later days or weeks, about wifi card.

767
Hardware / Re: Which buy a new laptop? for 2016
« on: January 26, 2016, 10:07:45 am »
Quote
I doubt if that  is actually true. You will probably find that some programs will run out of memory because of it.
You know tell me some program to test?
 I basically just used for this test, the firefox, with more than 20 open windows, and two running youtube videos without any problem.
 I hope you're wrong.
But you tend to be right, particularly with updating the ecs21 and restore this pc.

Quote
Whit this protocol.ini with NBAPI:
I update the E100E multimac from Arcanoae after this error.

Quote

I am not sure what that is, but you still have NETBIOS over TCPIP (TCPBEUI) in your configuration. It is confusing things. You should try only the WiFi adapter, with TCP/IP to keep things simple. Your Protocol.ini should look like:
Yes, but if I get the protocol.ini that you send me only with tcpip, I config.sys errors at startup. I tested all possible starts with one or two adapters and one or two protocols. And even with an adapter before another. And changing the IBMLAN.INI positions 34 and 35 from 0 to 1.Without improving anything . And leaving as before.



768
Hardware / Re: Which buy a new laptop? for 2016
« on: January 25, 2016, 10:14:22 pm »

Quote
I seem to recall that you may need to REM some of the statements in CONFIG.SYS. You cannot use the eCS 2.1 CD to work with an eCS 2.2 b2 system (for many things). It does insist that you use the proper version.
Yes, i have to begin  to rem many lines.

Quote
You did reboot, right?
In all cases rebot , but i made many combinations, of adapters and protocols, in same cases the condig.sys give me diferent errors in the net.

I have found that 1536 is best. I have problems if I make it less, and I have a different set of problems if I make it more. At 1536 I still see both sets of problems, but not as often.
[/quote]
Yes, but not in all cases is the same. This works better with more memory.

After several reboots I've only found these lines that may be of interest:
IBM OS/2 TCPBEUI 6.00.0
LT00018: The unrecognized keyword NBAPI was found in PROTOCOL.INI.

Whit this protocol.ini with NBAPI:
IBM OS/2 LAN Netbind
PRO0025: An error occurred when the program tried to bind TCPIP_NIF to W8086x4239_nif.

The protocol.ini not generate the same description in all cases, in fact I can not have it both adapters at the same time in the MPTS, that does not work either. Only one at a time.


protocol.ini
[PROT_MAN]

  DRIVERNAME = PROTMAN$

[IBMLXCFG]

  TCPIP_NIF = tcpip.nif
  tcpbeui_nif = tcpbeui.nif
  W8086x4239_nif = W8086x4239.nif

[NETBIOS]

  DriverName = NETBIOS$
  ADAPTER0 = TCPBEUI$,0

[TCPIP_NIF]

  DriverName = TCPIP$
  Bindings = W8086x4239_nif

[tcpbeui_nif]

  DriverName = TCPBEUI$
  Bindings = W8086X4239_NIF
  NBAPI = "YES"
  NODETYPE = "B-Node"
  OS2TRACEMASK = 0x0
  SESSIONS = 130
  NCBS = 225
  NAMES = 21
  SELECTORS = 15
  USEMAXDATAGRAM = "NO"
  NETBIOSTIMEOUT = 500
  NETBIOSRETRIES = 2
  NAMECACHE = 1000
  PURGECACHE = 0
  PRELOADCACHE = "NO"
  NAMESFILE = 0
  DATAGRAMPACKETS = 20
  PACKETS = 50
  ENABLEDNS = 0
  INTERFACERATE = 2

[W8086x4239_nif]

  DriverName = WRND32$
  VENDOR = 0x8086
  DEVICE = 0x4239
  NDIS_SYS = "netw5x32.sys"
  NDIS_INF = "netw5x32.reg"
  SSID = "WLAN"
  DEBUGLEVEL = "NONE"
  OPTIONS = "NONE"

Saludos

769
Hardware / Re: Which buy a new laptop? for 2016
« on: January 25, 2016, 09:35:17 pm »
I very much doubt that it has anything to do with ACPI. 
Yes is keyboard problem, but are very sensitive only to run his fingers over it and begins to write, or move the volume that does not sound,  :) :) :)
I have not been able to get away, I'll look later.
saludos

770
Hardware / Re: Which buy a new laptop? for 2016
« on: January 25, 2016, 01:25:49 pm »
Quote
Use (Network) Adapters and Protocols to remove all adapters, except the WiFi that you want to work with. Use only the TCP/IP protocol, and see what LANTRAN.LOG says, after a boot.

I can not with ecs22b2 define TCP-IP only because it gives me an error at startup with netwsta.200, I think it's an error in the IBMLAN.INI. Try reinstalling all the full support from the ecs21 networks, but do not let me install it asks me to insert the CD ecs22 and this does not solve the problem.

Quote
Also make sure that if you are using NAPS, that you have the updated one.

The problem is the same with mpts


Quote
Interesting. It seems that the 6300 and the 6200 are identical
yes

Quote
If one works, the other should too.
I hope so

 
Quote
For now, stay with only one device, and only the TCP/IP protocol, to keep it simple.
Yes, you are rigth.

I'm thinking to install the ecs21 update in other laptop and restore in this, and try again.
 
What I can say is that if I increase the memory in me CONFIG.SYS and was perfect with ecs22b2:
set VIRTUALADDRESSLIMIT=3072

771
Hardware / Re: Which buy a new laptop? for 2016
« on: January 24, 2016, 05:30:09 pm »
Another problem, I think that this is with ACPI
When i push the button for less volumem in a editor show cccc the 'c'  letter and
with the button for more volumem in a editor, cmd, etc show bbbb the 'b' letter one letter by one click.

saludos

772
Hardware / Re: Which buy a new laptop? for 2016
« on: January 24, 2016, 02:04:38 pm »
Quote
thanks,
I attach the file.

Okay, PCI says the 6200 is an 8086:4329. That was not in the available devices, so I took a guess and added it to GenMU_TEST-0-4-5.wpi. Intel seems to be pretty consistent in their drivers, so that will probably work, IF you can get the radio to turn on. I suspect that you won't be able to do that.

You need to install using the WarpIn installer, which makes the proper files available, THEN you need to use (Network) Adapters and Protocols to configure it properly.

I don't see the 6300 in the file...

Good luck...
Bad news, is not working.
In the sample below Genmac boot ... green:
NO VALID HARDWARE-INFO IN PROTOCOL.INI FOR WRND32 $

In lantran.log:
IBM OS/2 LANMSGDD [05/21/04] 6.00 is loaded and operational.
IBM OS/2 TCPBEUI 6.00.0
TCPBEUI: Using a 32-bit data segment.
IBM OS/2 NETBIOS 4.0
Adapter 1 has 223 NCBs, 130 sessions, and 20 names available to NETBIOS applications.
NETBIOS 4.0 is loaded and operational.
IBM LANVDD is loaded and operational.
IBM OS/2 LAN Netbind
PRO0025: An error occurred when the program tried to bind TCPIP_NIF to W8086X4239_nif.
TCPBEUI: Logical adapter 1 is trying to bind to TCP/IP interface lan0.
LT00141: Errors occurred while attempting to initialize TCPBEUI.

In scanx:
[C:\ecs\system\genmac\bin]scanx
DosOpen WRND32$ failed with error 110 at 304
Exiting with rc 110

Modified, the file protocol.ini, debug = ALL.
And create a cmd with type wrnddb$ >genmac.log that include in the startup folder,
but not give me any info.

saludos

I have installed windows 7 32 bits, in the same pc, and I got some information from which the attached file. Here you can see how w7, plays this card as N 6300

773
Hardware / Re: Which buy a new laptop? for 2016
« on: January 24, 2016, 02:13:56 am »
thanks,
I attach the file.
I can not acces to ftp://genmac@ftp.os2voice.org/ ask me for a password.

Saludos

774
Hardware / Re: Which buy a new laptop? for 2016
« on: January 23, 2016, 07:44:58 pm »
Modifications
webcam :   do not have
wifi : Is a Intel Centrino N6200 in pci-dock, and N6300 in w7. Do not work by now.
esata :  do not tested
usb 2.0 is ok 3 ports
usb 3.0 not work 2 ports
bluetoth : do not work
network :  Run with E1000 driver in install.
I attach the pci-dock file for full description if any need it.

saludos

775
Hardware / Re: Which buy a new laptop? for 2016
« on: January 23, 2016, 05:35:17 pm »
Thanks Martin, I edit soon with some minor modifications.
But I wanted to report a bug in NAPS.exe, it is the new MPTS, if all network adapters are erased, then you can not add new ones. With an error in protocol.ini
saludos

776
Hardware / Re: Brother-HL-2035 not printing ? ? ?
« on: January 23, 2016, 03:32:36 pm »
Brother-HL-2035 not printing after two years of struggle with CUPS.
Sorry, I misunderstood the question, I thought the cups used with for two years, and now I had rounded by function.
saludos

777
Hardware / Re: Which buy a new laptop? for 2016
« on: January 23, 2016, 11:48:34 am »
Summarizing the first impressions:
The new ACPI ver3.23.01, works perfect, a maximum resolution of 1280x800 monitor with panorama with beta2 ecs22.
Only at first the mouse on the websites, to an annoying flicker that has been removed and not know why.
The wifi I can not start it, although I have seen various web sites
http://ru.ecomstation.ru/projects/genmac/?action=unsupported
and the links on this page. I guess I need a file NETwNs32.reg.
but I am not clear how to create it.
The sound not sounds, but catches my attention that when you start the airboot, a blue light indicating a speaker at startup that light turns orange indicates banned or off, and when I turn off the system, turn it on again and it makes some noises from the speakers, seconds after it is turned off.
saludos

778
Hardware / Re: Brother-HL-2035 not printing ? ? ?
« on: January 23, 2016, 11:18:42 am »
My questions are very silly, but ...
1-You can print a test page
2-You can have the broken wire or disconnected
saludos

779
Hardware / Re: Which buy a new laptop? for 2016
« on: January 19, 2016, 11:48:28 pm »
Today I received an HP EliteBook 8540w, second-hand, with i7 processor, along with new ACPI Arcanoae. After a few hours of use, it shows me 8 processors, oddball stable. The wifi does not work, the network if it works and does not work HD sound.
saludos

780
Comments, Suggestions & Questions / Re: dbExpert
« on: January 17, 2016, 06:45:08 pm »
Hey there
I attached a small file, dbet001.htm, with some tricks and ideas collected from various forums, with some own.
This in English, Spanish, German, and other languages.
I hope you serve.
Saludos

Pages: 1 ... 50 51 [52] 53 54