Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Pete

Pages: [1] 2 3 ... 86
1
Programming / Re: Wdsibyl crash
« on: March 08, 2024, 09:11:38 am »
Hi Doug

I have seen that message after a hard disk crash corrupted some files, had to rebuild the project interface.

For the error messages about eg TMAIN1 see the project SPR file in the project source directory, open it with Text Editor - do not doubleclick it as that will start WDSibyl instead. You will probably find you need to manually add in any missing paths especially in the section called [Project Files].


Hope the above is of help

Pete

2
Applications / Re: Test build of dooble with qt5
« on: February 23, 2024, 03:47:23 pm »
Hi Dave

That command may work for qt6 but not qt5  as I get

SYS1041: The name qwebengine_convert_dict is not recognized as an
internal or external command, operable program or batch file.


No "howto" in the zip file.


Regards

Pete


3
Applications / Re: Test build of dooble with qt5
« on: February 23, 2024, 06:54:08 am »
Hi Dave

Same warning - this is in Settings.
Should there be *.bdic files in the zip package?


Regards

Pete



4
Applications / Re: Test build of dooble with qt5
« on: February 23, 2024, 06:33:49 am »
Hi Dave

Installed the dictionary files and set the environment path to J:\usr\share\qt5\qtwebengine_dictionaries\en
Doodle gives the warning that it cannot find file J:\usr\share\qt5\qtwebengine_dictionaries\en\en_GB.bdic - not surprising as it is not in the zip package. I wonder, Do the *.dic files need to be renamed to *.bdic ?


Regards

Pete

5
Setup & Installation / Re: CUPS tripped up SeaMonkey and Firefox
« on: February 10, 2024, 03:29:16 am »
Hi beregond

The program Dave Yeo is referring to is probably prndrv.exe which can be found here  https://www.os2site.com/sw/comm/fax/prndrv.zip

Enter prndrv on the command line to get a list of options.


Regards

Pete

6
Setup & Installation / Re: CUPS tripped up SeaMonkey and Firefox
« on: February 09, 2024, 03:37:40 am »
Hi beregond

I have seen this problem in the distant past and think it was basically an out-of-memory error caused by experimenting with cups and generating a large non-printing print queue. I think the only solution is to move cups daemon from the Computer -> Startup folder (move it into Computer) and reboot then check that Seamonkey starts.

If that is successful you will then need to clear the cups print queue.

With Seamonkey running doubleclick cups daemon to start cups.
Point Seamonkey to cups admin gui at http://localhost:631
Click on the Printers tab
Click on your printer
In the Maintenance dropdown box select Cancel All Jobs
In the Administration dropdown box select Modify printer to check the printer settings are correct
Move cups daemon back into the Startup folder

Hope the above is of help

Pete




7
Comments, Suggestions & Questions / Re: USB to Parallel
« on: February 08, 2024, 12:59:08 am »
Hi Martin

Yes, cups works with usb printers - or did last time I tried a few years ago. Does not use the usbprt.sys driver, uses libusb/usbcalls for output.
No idea if that would work better/faster with a usb to parallel lead though...


Regards

Pete

8
Hardware / Re: The last nail in OS/2's coffin
« on: February 02, 2024, 06:51:09 pm »
Hi All

I have to join in to say that I have been looking for a replacement OS since IBM announced OS/2's demise in 2000(?) and have not found anything that I am as happy to use.

The main problem I am currently bumping into is the same as everyone else: We do not have a capable browser. Seamonkey (and, I guess, Firefox) no longer work very well - if at all - on a lot of websites; Doodle (qt5) is simply too flaky to use due to crashes and system hangs.

Thanks to all who have kept OS/2 alive to date.


Regards

Pete

9
Hi Doug

I think all later/current mainboards have the warning about only supporting 64 bit OS's - my B450 does but that does not stop AOS 5.1 from installing and running.


Regards

Pete

10
Hi All

It's possible the x600 is failing - must be fairly old by now  :-)
I had a x600pro a few years back which started to fail, could only be used in VBE mode as switching to accelerated mode resulted in a badly messed up display.

If Doug wants a recommendation for a replacement card the Radeon RX550 works fine with the Panorama driver.


Regards

Pete

11
Setup & Installation / Re: Are there any 8GB Nvme compatiable motherboard
« on: January 21, 2024, 11:06:35 am »
Hi Doug

This is "on the wiki" and works quite well  https://www.os2world.com/wiki/index.php?title=MSI_B450M_PRO-VDH_MAX

After boot and with Seamonkey running this is the output from mem/v

H:\sys\bin>mem /v

Total physical memory:     14,271 MB
Accessible to system:       3,036 MB
Additional (PAE) memory:   11,235 MB

Resident memory:              259 MB
Available virtual memory:   2,827 MB

Available process memory:
  Private low memory:         278 MB
  Private high memory:      1,792 MB
  Shared low memory:          199 MB
  Shared high memory:       1,587 MB


Regards

Pete


12
Hi All

I seem to have found a problem with DFSee 17 and creating Desktop objects.
In the dfsee bin directory is the file dfswpobj.cmd which is meant to create all DFSee Desktop objects.
When I run that file it reports lots of objects created successfully - and nothing appears on the Desktop.
Anyone else seeing this? - you will need to delete existing DFSee Desktop objects to test this so I suggest Desktop backup *before* testing.


Regards

Pete

13
Hi Andrew

Can you print from QP?
If "Yes" , select to Print then select Properties.
Select the Output tab then check Print to Raw Postscript File and enter where to save file to.
Then you can use [Unixroot]:\usr\bin\ps2pdf.cmd to convert from PS tp PDF eg

J:\USR\BIN>ps2pdf S:\Backups\H\18032011\test.ps S:\Backups\H\18032011\test.pdf

J:\USR\BIN>


The above converts a 2 page PS file to a 2 page PDF file successfully, Lucide has no problems displaying it.


Hope the above helps

Pete

14
Hi David

Still available on the website http://www.ca-arnold.de/


Regards

Pete


15
Hi Dave

Memory nudge: daniatapi.flt replaces the 2 files IBMATAPI.FLT and IBMIDECD.FLT


Regards

Pete
 

Pages: [1] 2 3 ... 86