FIXED IDE HARD DRIVE AND REMOVABLE MEDIA SUPPORT October 7, 2005 OS/2 Device Driver Development IBM Solution Technologies Austin, TX (c) Copyright International Business Machines Corporation, 2001, 2005. All rights Reserved. CONTENTS ________ Prerequisite Support 1 Introduction 2 Installation 2.1 Updating the Installation Diskettes 2.2 Updating a Previously Installed Warp System 2.3 Recommended Parameters for IBM1S506.ADD 2.4 Recommended Parameters for IBMATAPI.FLT and IBMIDECD.FLT 2.5 Recommended Parameters for IBM1FLOPPY.ADD 3 Large Hard Drive Considerations 3.1 System Hang or Hard Drive Hesitation 3.2 Cannot Mark a Partition Installable 3.3 IPE on Boot, "Trap D" 3.4 Inconsistencies in Total Disk Space 3.5 Application Install Fails with "Not Enough Space" 3.6 Performance Problems With Two Devices on a Single Channel 3.7 Install Diskettes or Utility Diskettes Hang on Boot (APAR JR12065) 3.8 Additional Parameters For IDE Device Driver 3.9 Very Large (128/137 Gb limit) Hard Drive Considerations (48 bit LBA) 3.10 Very Large (512 Gb limit) Hard Drive Considerations 3.10.1 Format Error Installing from Updated Diskettes 3.10.2 Installation Process Hangs after Rebooting When Installing from Updated Diskettes 4 Removable media support 4.1 Partitioned Removable Media 4.1.1 Using Protected Media 4.1.2 Assignment of Drive Letters 4.1.3 Configuring Partition Support (OS2DASD) 4.1.4 Ejecting the Media 4.1.5 Limitations of Partitioned Removable Media Support 4.2 Large Floppy Removable Media (LS-120 / LS-240) 4.2.1 Limitations of LS-120 / LS-240 Support 4.3 CD-ROM Device Manager (OS2CDROM.DMD) 4.4 CD-RW Media Support in IBMIDECD.FLT and IBMATAPI.FLT 4.5 Additional Parameters for IBMIDECD.FLT and IBMATAPI.FLT Driver 5 Supported Chipsets, Known Restrictions and Limitations 5.1 Supported Chipset Table 5.2 Known Restrictions and Limitations 5.2.1 Intel Chipsets Limitations 5.2.2 VIA Chipsets Restrictions 5.2.3 SiS Chipset Limitation 5.3 Chipset Extended Detection Algorithm for Intel Chipsets 5.4 Serial ATA for Intel Chipsets Considerations 5.5 Intel 82801FR and 82801GR support in IBM1S506.ADD 6 Copyright and Trademark Information Prerequisite Support ________________________ The Latest OS2 Loader package from DDPAK should be applied to your system (or installation diskettes) prior to installing this IDEDASD package. 1 Introduction _________________ FixPak 35 (FP35) for Warp 3 and FixPak 6 (FP6) for Warp 4 extended support for fixed Enhanced IDE drives to sizes up to 8.4GB and added new caching HPFS and FAT file system support for removable media drives such as SCSI Syquest Syjet 1.5GB portable hard drive and the Iomega jaz 1GB and 2GB personal hard drives. This package contains updates to the support in FP35 and FP6, extending support to fixed Enhanced IDE drives first past the 8.4GB boundary and second past the 512 Gb boundary. It also fixes some other problems, and adding additional documentation on removable media support. Beginning with FP40 and FP10 OS/2 base device drivers were separated into a Base Device Driver FixPak. File ddk_note.txt contains programming information related to the drivers included into the IDEDASD package and can be used in addition to the DDK and SDK references. This package also contains extensions to OS2CDROM.DMD, providing support for multi-session CDROM media. The package also contains an updated floppy diskette driver (IBM1FLPY.ADD), which corrects a failure that occurs upon a Resume on a ThinkPad when the diskette drive is installed in the ThinkPad docking station. Previously IDE CD-ROM (also CD-R, CD-RW, DVD) devices were handled by IBMIDECD.FLT and all other ATAPI devices (like LS-120 and ZIP drives) were handled by IBMATAPI.FLT. Now all ATAPI devices are handled by a single driver, the IBMATAPI.FLT. For backward compatibility this package provides both IBMIDECD.FLT and IBMATAPI.FLT drivers. In fact, they are the same driver and if both drivers are in config.sys only the first one in config.sys will remain loaded. It is recommended to use only IBMATAPI.FLT driver entry and remove the IBMIDECD.FLT entry from config.sys. If you do not remove the IBMIDECD.FLT entry from the config.sys, the step in section 2.4 must also be performed on the IBMIDECD.FLT entry. For Warp Server Advanced HPFS386 support of removable media, you additionally need LAN Server SelectPack IP_8508. These fixpaks are available from http://ps.software.ibm.com/ under the link "Downloads and News." Install the fixpaks first, carefully following the instructions with the fixpaks; then follow the directions in this README to install this package. If you are attempting to install Warp 3 or Warp 4 for the first time on a fixed hard drive greater than 4.3GB, then: 1. Follow the instruction on "Updating the Installation Diskettes" in this README and use the new diskettes to install Warp. 2. Install FP35 for Warp 3 or FP6 for Warp 4. 3. Follow the instructions in this README to install this package. The file list for the package: - dasd16.dmd - dasd16.sym - dasd32.dmd - dasd32.sym - ddk_note.txt - ibm1flpy.add - ibm1flpy.sym - ibm1s506.add - ibm1s506.sym - ibmatapi.flt - ibmatapi.sym - ibmidecd.flt - ibmidecd.sym - ide16.ddp - ide32.ddp - os2cdrom.dmd - os2cdrom.sym - readme.txt 2 Installation _________________ 2.1 Updating the Installation Diskettes ________________________________________ If you are attempting to install Warp on a hard drive greater than 4.3GB, or your are attempting to install Warp Server for e-business on a hard drive greater than 30GB, then the Installation diskettes must be updated. If you are intend to install OS/2 on a hard drive greater than 512 Gb partitioned by OS/2 without OS2DASD.DMD parameter /D:n /BOOTABLE or by non-OS/2 tool, you should back up all data from the all partitions on this drive, then remove all partitions from the drive and reboot, before you start installation process. This is because OS/2 cannot currently make bootable such a drive with an acknowledged capacity larger than 512 Gb. Instead the drive must first be changed to use a smaller logical geometry which ignores part of the true capacity. This backing up process is typically laborious for a drive which is already in use; and this is why it is important to make an early and deliberate and selection of /BOOTABLE versus /FULLSIZE option for each drive with greater than 512 Gb capacity when using this version of OS2DASD.DMD on a new drive. 1. Make a backup copy of your Diskette 1 (D1). 2. Copy the new versions of IBM1S506.ADD, and IBMIDECD.FLT device driver files onto your D1 diskette. 3. If the installation diskettes are for Warp Server for e-business, Warp Server for e-business Convenience Pak, or Warp 4 Convenience Pak, copy the DASD32.DMD file to your D1 diskette as (over the existing) OS2DASD.DMD. Otherwise copy the DASD16.DMD file to your D1 diskette as (over the existing) OS2DASD.DMD. 4. Modify the CONFIG.SYS file: a. Add the statement SET COPYFROMFLOPPY=1 to the CONFIG.SYS on D1. b. Add the parameters /D:n /BOOTABLE to the line BASEDEV=OS2DASD.DMD in the CONFIG.SYS on D1 (/D:n refers to the intended boot drive, see section 3.10 for parameters details) for disks equal or larger than 512 Gb. 5. Start the installation with the Installation Diskette and follow instructions. NOTES: a. During the installation process before rebooting your system make sure that the device driver statements are in the CONFIG.SYS file and the new versions of the IBM1S506.ADD, IBMIDECD.FLT and OS2DASD.DMD device drivers have been copied to the \OS2\BOOT directory. Use the date of the files to distinguish the newer versions. b. (Follow this note instructions if your total disk capacity is larger than 512 Gb.) During installation process, you will be prompted to reinsert all diskettes and the files will be copied from the diskettes to the hard drive. After coping and before rebooting (you will see the message "Remove the diskette and press Enter to restart the workstation and continue the installation") you must exit to command prompt (using F3) and remove duplicate line containing "BASEDEV=OS2DASD.DMD /D:n /BOOTABLE" from ending of the CONFIG.SYS. There should remain the line "BASEDEV=OS2DASD.DMD" in the middle of the CONFIG.SYS. 2.2 Updating a Previous Installed Warp System ________________________________________________ 1. (Optional) Save the existing (old) level of drivers in your system. a. Change Directory to the \os2\boot directory on your boot drive. b. Rename the drivers (for example, where the boot drive is C:). The IBMATAPI.FLT driver may not have been previously installed. [C:\os2\boot] rename IBM1S506.ADD IBM1S506.ORG [C:\os2\boot] rename IBM1FLPY.ADD IBM1FLPY.ORG [C:\os2\boot] rename IBMIDECD.FLT IBMIDECD.ORG [C:\os2\boot] rename IBMATAPI.FLT IBMATAPI.ORG [C:\os2\boot] rename OS2CDROM.DMD OS2CDROM.ORG [C:\os2\boot] rename OS2DASD.DMD OS2DASD.ORG 2. Open an OS/2 Window and enter the SYSLEVEL X: (where X: is your boot drive). Look for the entry x:\OS2\INSTALL\SYSLEVEL.OS2 and see which version of OS/2 you have installed; for example "Version 4.00" or "Version 4.50". 3. Device Driver Install o (Warp 3, Warp Server) Open the Device Driver Install program in the OS/2 System Folder/System Setup Folder. o (Warp 4, Warp Server for e-business) Open the Device Driver Install program in the OS/2 System/System Setup/Install-Remove Folder. 4. Point the Device Driver Install file dialogue to the directory where you have placed the new files in this package. If your version of OS/2 is 4.00 or earlier, select the driver named IBM IDE AND REMOVABLE MEDIA SUPPORT (V4.00). If your version of OS/2 is 4.50 or later, select the driver named IBM IDE AND REMOVABLE MEDIA SUPPORT (V4.50). Click on INSTALL. 5. Reboot the system. 2.3 Recommended Parameters for IBM1S506.ADD _________________________________________ For normal functioning of Extended WarmSwap support IBM1S506.ADD must be configured as follows: 1. Edit config.sys 2. Find the line with IBM1S506.ADD: "BASEDEV=IBM1S506.ADD" 3. Add (if they aren't already there) the following parameters: "BASEDEV=IBM1S506.ADD /A:n /U:m /ATAPI /FORCE" where n is adapter number and m is unit number. 4. Save config.sys 5. Reboot Examples: "BASEDEV=IBM1S506.ADD /A:1 /U:0 /ATAPI /FORCE" enables swapping on ThinkPad Ultrabay. "BASEDEV=IBM1S506.ADD /A:2 /U:0 /ATAPI /FORCE" enables swapping on DockingStation Ultrabay. See section 3.8 for description of these parameters. 2.4 Recommended Parameters for IBMATAPI.FLT and IBMIDECD.FLT ____________________________________________ For normal functioning of WarmSwap support IBMATAPI.FLT must be configured as follows: 1. Edit config.sys 2. Delete line with IBMIDECD.FLT (see note below): "BASEDEV=IBMIDECD.FLT" 3. Find the line with IBMATAPI.FLT: "BASEDEV=IBMATAPI.FLT" 4. Add (if they aren't already there) the following parameters: "BASEDEV=IBMATAPI.FLT /A:n /U:m /TYPES:CLZ" where n is adapter number and m is unit number. Theymust be the same as for IBM1S506.ADD (see sect. 2.3 for details) 5. Save config.sys 6. Reboot Examples: "BASEDEV=IBMATAPI.FLT /A:1 /U:0 /TYPES:CLZ" enables swapping of LS-120, LS-240, ZIP, CD type devices in ThinkPad Ultrabay. "BASEDEV=IBMATAPI.FLT /A:2 /U:0 /TYPES:CLZ" enables swapping of LS-120, LS-240, ZIP, CD type devices in DockingStation Ultrabay. See section 4.5 for description of these parameters. Note: If you do not remove the IBMIDECD.FLT entry from config.sys, then step 4 must also be performed on this entry. 2.5 Recommended parameters for IBM1FLOPPY.ADD ______________________________________________ To enable external and ultrabay floppy drive functioning with WarmSwap IBM1FLOPPY.ADD must be configured as follows: 1. Edit config.sys 2. Find the line with IBM1FLPY.ADD: "BASEDEV=IBM1FLPY.ADD" 3. Add (if they aren't already there) the following parameters: "BASEDEV=IBM1FLPY.ADD /A:n /FORCE:2 /U:m /F:1.44MB /U:m /F:1.44MB" where n is adapter number and m is unit number. 4. Save config.sys 5. Reboot Example: "BASEDEV=IBM1FLPY.ADD /A:0 /FORCE:2 /U:0 /F:1.44MB /U:1 /F:1.44MB" 3 Large Hard Drive Considerations ____________________________________ 3.1 System Hang or Hard Drive Hesitation _________________________________________ The problem is the IDE chip sets on certain planars indicate that they support Bus mastering but actually have a defect that prevents them from working correctly. The driver detects bus mastering support, enables busmastering and attempts to use it. Some symptoms are: o System will not boot with IBM1S506.ADD. o CHKDSK command does not work properly. o Hard drive stops or hesitates for minutes at a time. This is a known problem with ThinkPad models 760E/ED/ELD/EL. However the chip set can, and does, show up on planars of other manufacturers. To correct: 1. Edit the CONFIG.SYS file on Diskette 1 or the boot drive. 2. Disable busmastering by adding the parameter /!BM to the driver; for example: BASEDEV=IBM1S506.ADD /A:0 /!BM /A:1 /!BM 3. Save the changes and reboot. 3.2 Cannot Mark a Partition Installable ________________________________________ There is a BIOS restriction for most older (typically pre-2001 manufacture) computers that installable (startable) or bootable partitions must be contained within the first 1024 logical cylinders of the disk. This is true for both EIDE and SCSI hard disk drives. If FDISK fails to allow a partition to be marked installable, the partition is either above 1024 cylinders or the partition spans the first 1024 logical cylinders of the disk. Use FDISK to reduce the size of the startable or bootable partition by sufficient MBytes. One way to calculate the correct partition size is to do the following: 1. Edit your CONFIG.SYS and add the parameter /W or /V to the BASEDEV=IBM1S506.ADD statement. 2. Save this change and reboot the system. 3. At initialization, record the far left hand column of numbers of the geometry information under the OS2:log heading; for example, where C=cylinder, H=head, and S=sector: OS2:log C 1027 H 63 S 128 4. Calculate the 1024 cylinder size in MBytes as ( H x S ) / 2. (round down). All bootable partitions must be contained within this size. In this example the bootable partition must be contained in the first 4032 MBbytes of the disk and cannot exceed a single partition size of 4032 MBytes within this area. No bootable partition may extend beyond the first 4032 MBytes. 5. Use FDISK to resize the partitions and reboot. 3.3 IPE on Boot, "Trap D" __________________________ If you experience a Trap D on boot when using the /FORCE parameter on IBM1S506.ADD, and you have the NetFinity client installed, REMark out the BASEDEV=NFDASD.FLT statement in CONFIG.SYS. 3.4 Inconsistencies in Total Disk Space ________________________________________ This version of IBM1S506.ADD allows the detection and correct reporting of some additional free space on certain drives. This "free space" is real and now can be accessed, either by creating a new partition or using a program such as PartitionMagic to add the free space to an existing partition. This will not cause any corruption or inaccessibility to the data currently on the disk. 3.5 Application Install Fails with "Not Enough Space" ______________________________________________________ FAT partitions under OS/2 are limited to a 2.1GB maximum size. HPFS partitions are limited to a 64GB maximum size. However there is the magic number, 2,147,483,647 (2.1GB). This 2.1GB value is the maximum number that will fit into a signed 32-bit integer. Some application software installation programs query OS/2 about the available remaining space on the partition and save the result into a signed 32-bit integer. If more than 2.1GB is available there is an overflow, it appears no space is available, and the installation program refuses to continue. Two solutions are: o Partition the remaining space into maximum 2GB partitions. o Retain the large partition, but before trying to install software create a large temporary file that reduces available space to less than 2.1GB. After installation of the application delete the temporary file. 3.6 Performance Problems with Two Devices on a Single Channel ______________________________________________________________ With certain planars, two devices attached to the same IDE channel will exhibit performance problems when one device is a slow non-DMA device like a CDROM or removable drive and the other device is a faster disk drive. To alleviate this problem move the slow device to the other channel, where it is the only device or is paired with a similar slow device. If moving the device is not possible, then you can disable busmastering for that channel, by specifying parameters on the driver IBM1S506.ADD in CONFIG.SYS. For example, if you wanted to disable bus mastering for the secondary controller, you would add the parameters "/A:1 /!BM" to the IBM1S506.ADD line in CONFIG.SYS. 3.7 Install Diskettes or Utility Diskettes Hang on Boot (APAR JR12065) _______________________________________________________________________ Diskette 1 of the Install or Utility diskette sets may appear to hang on boot, waiting for a removable media device to respond. To avoid: 1. Edit the CONFIG.SYS on Diskette 1 of the set 2. REMark out the basedev=ibmint13.i13 statement and save the file. 3. Reboot 3.8 Additional Parameters for IDE Device Driver ________________________________________________ PARAMETER FUNCTION /V Verbose Mode, displays controller status and drive geometry information during OS/2 initialization. /VL Same as /V but does not display drive geometry. This parameter is added to avoid the message buffer overflow, resulting in a "Lost message" message. /V:x Verbose Mode, displays controller status and drive geometry information only for selected adapter x. The x value can be from 0 to 4. This parameter is added to avoid the message buffer overflow, resulting in a "Lost message" message. /W Verbose Mode, displays controller status and drive geometry information during OS/2 initialization. Initialization stops after displaying the information for each device, with a "Press Enter to Continue" message. It is possible that the message buffer will overflow, resulting in a "Lost message" message. This parameter works correctly on Warp 3 with FP35 or later systems and on Warp 4 systems with FP6 or later. /WL Same as /VL, only with pause. Initialization stops after displaying the information for each device, with a "Press Enter to Continue" message. /W:x Same as /V:x, only with pause. Initialization stops after displaying the information for each device, with a "Press Enter to Continue" message. /FORCE Forces the emulation of an IDE CDROM drive, even though one is not present during OS/2 initialization. For example, the statements BASEDEV=IBM1S506.ADD /A:1 /U:0 /ATAPI /FORCE BASEDEV=IBMIDECD.FLT support inserting an internal CDROM drive into the Ultrabay of a ThinkPad 755CD after suspend, even though the drive is not present during initialization. /UDMA:x If the system is Ultra DMA capable, this parameter may be used to limit the highest UDMA mode for an adapter or device. The limit is specidied by "x", the value can be from 0 to 5. If the specified value is higher than the maximum UDMA capability the parameter is ignored. For example, the statement BASEDEV=IBM1S506.ADD /A:1 /U:0 /UDMA:2 limits Ultra DMA mode for secondary channel master device to Ultra DMA mode 2. /!UDMA This parameter is used to disable Ultra DMA modes of Bus Mastering but leave BM DMA modes enabled. For example, the statement BASEDEV=IBM1S506.ADD /A:0 /U:1 /!UDMA disables Ultra DMA mode for primary channel slave device. /BM If the system is DMA capable, this parameter can be used to enable or disable DMA for a specified device or adapter. Example: "/A:1 /U:0 /BM" enables DMA for the Master device attached to the secondary IDE channel. This can be useful to enable DMA on ATAPI devices ( CD-ROM, LS120, ZIP, etc) that are defaulted to run in PIO mode. If a device is UDMA capable, using the "/BM" or "/UDMA" parameter is recommended only if the IDE 80 pin flat cable is connected (instead of the normal 40 pin flat cable). See section 5 for details on various chipsets. /!BM This parameter is used to disable Bus Mastering DMA for an adapter or device. For example, the statement "BASEDEV=IBM1S506.ADD /A:1 /!BM" disables BM DMA for secondary IDE channel, "BASEDEV=IBM1S506.ADD /A:0 /U:1 /!BM" disables BM DMA for master device on primary IDE channel /!HC This parameter is used to disable a drive's internal write cache. When this parameter is specified and a write is issued to the device, the drive will write directly to the media and will not return until the data has been written to the media For example, the statement "BASEDEV=IBM1S506.ADD /A:0 /U:0 /!HC" disables write cache for the device located at Unit 0 on the Primary Adapter, "BASEDEV=IBM1S506.ADD /A:0 /!HC" disables write cache for all units attached to the Primary Adapter. /HC This parameter is used to enable device write cache. In general this parammter should not be needed because the default is Device Write Cache enabled. For example, the statement "BASEDEV=IBM1S506.ADD /A:0 /U:1 /HC" enables write cache for the slave device on the Primary Adapter, "BASEDEV=IBM1S506.ADD /A:1 /HC" enables write cache for all units attached to the Secondary Adapter. /!BIGLBA Disables 48 bit LBA support for specified drive. Drive size will be limited to 128 (137) Gb and legacy LBA 28 bit support will be used. See section 3.10 for details. Examples: "BASEDEV=IBM1S506.ADD /A:0 /U:0 /!BIGLBA" disables 48 bit LBA support for master device on primary IDE channel, "BASEDEV=IBM1S506.ADD /A:1 /U:1 /!BIGLBA" disables 48 bit LBA support for slave device on secondary IDE channel. /CDA Enables Chipset Extended Detection Algorithm for Intel chipsets. Example: BASEDEV=IBM1S506.ADD /CDA Enables detection of newer Intel PCI IDE chipset as the latest described in the supported chipset table in section 5.1. See section 5.3 for additional information about Chipset Extended Detection Algorithm. /!SAL Disables SMART (Self-Monitoring, Analysis, and Reporting Technology) Auto Logging for the device. This switch will disable SMART Auto Logging only for the device. It does not have an affect on any of the other SMART commands. Example: BASEDEV=IBM1S506.ADD /A:0 /U:0 /!SAL 3.9 Very Large (128/137 Gb limit) Hard Drives Considerations (48 bit LBA) ____________________________________________________________________________ Legacy LBA (also know as 28 bit LBA) maximum drive capacity is limited to 137 GB (268,435,455 sectors by 512 bytes each). The 48 Bit LBA support was introduced to break this barrier and provide support for hard disk with capacities larger than 137 GB. This version of the IBM1S506.ADD driver has the 48 bit LBA support and the driver will automaticaly detect drives with the capability of 48 bit LBA. This 48 bit LBA support will allow the use of hard disk drives with up to 2 TB (Terabytes) (1 TB = 1024 GB) capacity. In spite of the original removal of the 28 bit restriction, before the addition of 512 Gb logical geometry support, the OS2DASD.DMD driver also had a geometry imposed limitation which limited the maximum physical hard disk capacity which OS/2 could support to 512 Gb. To maintain backward compatibility a new config.sys parameter,"/!BIGLBA", is introduced. If "/!BIGLBA" is specify in config.sys, this parameter for the specfic drive will disable 48 bit LBA support and will revert to legacy 28 bit LBA and usable drive capacity will be limited to 137 GB (268,435,455 sectors by 512 bytes each). If the drive is partitioned when using this switch, then it will be compatible when connected to a system without 48 bit LBA support. See section 3.8 for the "/!BIGLBA" parameter syntax. 3.10 Very Large (512 Gb limit) Hard Drive Considerations ________________________________________________________ The previous version of OS2DASD.DMD had a 512 Gb geometry limitation which allowed only part (remainder of the total drive capacity divided by the 512 Gb) of the hard drive to be accessible for the system. The current version of OS2DASD.DMD removes this limit and allows total capacity of the hard drive up to 2 Tb. This support has the following options: 1. If the drive is used as a boot drive, only first 512 Gb of the drive space will be accessable to the system. 2. If drive is used only as a data storage drive the total capacity (up to 2 Tb) of drive will be accessable to the system. The two new parameters are available to select these options: o /BOOTABLE --- applied to the unpartitioned large drive (during the bootup prior to the first partitioning of the drive) and makes drive bootable, but limiting its available capacity to 512 Gb. o /FULLSIZE --- applied to the unpartitioned large drive (during the bootup prior to the first partitioning of the drive) and allow use of the total capacity of the drive (up to 2 Tb), but prevents the drive from being made bootable. The parameters have the following usage syntax: BASEDEV=OS2DASD.DMD [/D:n] [/BOOTABLE | /FULLSIZE] where /D:n denotes the number of the drive (/D:0 is drive 0, etc.). Parameter /BOOTABLE or /FULLSIZE following /D:n is applied to drive n. If for some drive value n (n>0) the /D:n parameter is omitted the following parameter (/BOOTABLE or /FULLSIZE) is applied to the first drive (default /D:0). If parameter /BOOTABLE or /FULLSIZE for some drive is omitted, /FULLSIZE is applied for this drive by default. If drive is larger than 512 Gb, then LVMUPDT package must be installed in addition to the IDEDASD package to access the full drive capacity (/FULLSIZE option). If drive is not larger than 512 Gb that IDEDASD package is enough to access the full drive capacity, but LVMUPDT package may be installed in addition. 3.10.1 Format Error While Installing from Updated Diskettes ___________________________________________________________ If you get a format error message while installing OS/2 from updated diskettes, check whether you have the following line in the CONFIG.SYS: BASEDEV=OS2DASD.DMD /D:n /BOOTABLE If instead you have the line: BASEDEV=OS2DASD.DMD without the parameter /BOOTABLE for the intended boot drive /D:n, then you will need to: 1) Stop your current installation of OS/2 2) Backup any data which you intend to preserve from the all the partitions on the intended boot drive /D:n which you intend to preserve 3) Remove all the partitions on the intended boot drive /D:n 4) Reboot 5) Modify your CONFIG.SYS file on the D1 diskette to add /D:n /BOOTABLE, if it is not there already 6) Restart the installation process of OS/2 from the beginning 7) Restore backed up data to new partitions using the new logical geometry Since all this backing up and restoring is typically quite inconvenient, it is highly advisable to decide quite deliberately whether or not you intend to use your large drive as a boot drive before you partition it and modify your CONFIG.SYS file on your D1 diskette accordingly, as previously documented. 3.10.2 Installation Process Hangs after Rebooting When Installing from Updated Diskettes ____________________________________________________________________________ If the installation process hangs after rebooting when installing from updated diskettes, then see section 3.10.1 for possible reason and recovery instructions. 4 Removable Media Support __________________________ Removable media devices attach to the system by a variety of interfaces. IDE Supported with the OS/2 supplied IBM1S506.ADD device driver. EIDE Supported with the OS/2 supplied IBM1S506.ADD device driver. ATAPI Supported with the OS/2 supplied IBMATAPI.FLT device driver. ATA Supported with the OS/2 supplied IBM1S506.ADD device driver. Iomega Zip ATA drives are supported only as single partition media and be configured in ATA Compatibility Mode; that is, the jumpers are: Master Slave þ þ SCSI Small Computer System Interface. Supported with the OS/2 device driver for the SCSI controller to which the device is attached. Many SCSI drivers are supplied with OS/2. If your device is not recognized you must acquire the proper device driver from the vendor. Consult http://service.software.ibm.com/os2ddpak/html/diskands/index.htm. To ensure correct operation with the Adaptec 1542 SCSI adapter, partition sizes should always be less than 1GB. PP Parallel Port attached devices are supported with vendor-supplied drivers. The device driver must have an ".ADD" extension for the media to be supported as partitioned removable. For example, the Syquest Syjet Parallel drive is properly supported by the vendor-supplied EPST.ADD driver, the Iomega Zip Parallel uses a vendor-supplied *.SYS driver and is not supported by the partitioned removable support, and the Syquest SparQ Parallel Iomega ZipPlus Parallel drives have no OS/2 drivers at all. USB Floppy and removable media devices (including CDROM, CD-RW devices) are supported with the OS/2 supplied USBMSD.ADD device driver and special CDROM class device driver USBCDROM.ADD. Removable media devices are supported in one of two ways. LARGE FLOPPY The LS-120 / LS-240 drive. PARTITIONED All other magnetic removable media devices. This media appears as a removable hard drive. 4.1 Partitioned Removable Media ________________________________ Features of the partitioned removable media support are: o Ability to partition removable media into multiple partitions o Ability to format with either HPFS or FAT o Ability to exploit caching performance o Ability to use HPFS long file names o Drag/drop capability through the Workplace drive icon o Operating system protection to safely eject media through software eject utility o Assignment of drive letters to end of disk drive lettering chain to prevent floating drive letters o Ability to predetermine a fixed number of drive letters for multiple partitions for removable media 4.1.1 Using Protected Media There are some restrictions on the use of these devices. These restrictions deal with vendor-provided protection routines that either read/write or password protect the media. You are unable to read or write HPFS formatted media that has been read, write or password protected by a vendor supplied protection utility. For all read and write protected media, remove the vendor protection prior to trying to read or write to the media. For instance, if you do not remove the protection, you will get the following failures: o If you issue a DIR command to write or password protected media, you will receive a "Drive improperly stopped" error message. o If you try to FORMAT a write or password protected media, you will receive numerous error messages after a few minutes. o If you try to use desktop operations like drag/drop folders/files, you will receive numerous error messages. Once the vendor supplied protection is removed, then these errors will no longer occur. 4.1.2 Assignment of Drive Letters New Algorithm: no filters assumed Primary from fixed disk 1 Primary from fixed disk 2 Primary from fixed disk n Extended from fixed disk 1 Extended from fixed disk 2 Extended from fixed disk n Primary from removable disk 1 Extended(s) from removable disk 1 Primary from removable disk 2 Extended(s) from removable disk 2 Primary from removable disk n Extended(s) from removable disk n Lack of a primary partition (or Extended Partition only) is allowed. If no media is present at boot, a single logical drive is reported. Note that some drives, Syquest EZ135A for example, do NOT report correctly when no media is present and will not be seen at all. If media with multiple partitions is present at boot, then all partitions will be assigned drive letters. 4.1.3 Configuring Partition Support (OS2DASD) BASEDEV=OS2DASD.DMD [/LF] [/MP:(disk,count)[,(disk,count)]] PARAMETER DESCRIPTION /LF Forces all removable devices to be treated as Large Floppy rather than partitioned media. /MP Used to support allocating a predetermined number of drive letters for a partitioned removable media device. Note that this option only applies to partitioned removable devices, and is ignored for any other device type. If the /MP parameter is used, then: SUB-PARAMETER DESCRIPTION DISK The integer disk number of the device, as reported by FDISK, or the wildcard character * to specify all partitioned removable devices. COUNT The integer count of the number of partitions to reserve for the device. If the wildcard character * is used, it specifies a default number of drive letters to reserve for all partitioned removable devices. Specifying a count for a particular disk will override this default. Also, if there is media in the device at boot time, and it has more partitions which are eligible to receive drive letters than there are drive letters reserved for the device through the /MP option, then the number of drive letters reserved for the device will be increased so that every eligible partition on the media will have a drive letter. If the /MP option is not used, the rules for determining the number of drive letters reserved for a partitioned removable media device are as follows: o If there is no media in the drive at boot time, or the media in the drive has no valid partitions, then one drive letter is reserved for the device. o If there is media in the drive at boot time and the media has valid partitions which are eligible for drive letters, the number of drive letters is equal to the number of eligible partitions on the media. Media which is formatted in floppy mode is treated as a single partition and allocated a single drive letter. 4.1.4 Ejecting the Media OS/2 prevents the media from being ejected during data transfers or while there are pending file transactions. The hardware manual eject button is disabled during these times. The eject button will be enabled when the media can be safely ejected. There is a new OS/2 utility, EJECT.EXE, that provides a command line method for ejecting the media. The Workplace Drive Icon now supports the software eject option for these drives as well. For example, the command EJECT J:, where J: is the logical drive letter of one of the partitions on the media will cause the media to be ejected. In order for this command to succeed there must be no open files on any of the partitions on the media, nor any open search operations. Removable media that is shared on a server cannot be ejected because of open file handles. If it is necessary to remove the media without rebooting you may issue the command CHKDSK J: /F, where J: is the logical drive letter of one of the partitions on the media. This will free the media and a subsequent EJECT J: command will cause the media to be ejected. 4.1.5 Limitations of Partitioned Removable Media Support o Applications that manipulate partitioned devices, such as file managers, must be updated to test the fixed/removable flag in order to account for partitioned removable devices. Such applications that have not been updated treat the removable devices as fixed and the results are unpredictable whenever media is not present. o Due to the variability of hardware adapter support, installing to or booting from partitioned removable media is not supported. o Optical drive support is unchanged. Partitioned removable media and HPFS do not support optical drives. You should continue to use OPTICAL.DMD and OS2SCSI.DMD. o The following devices were tested during the development of the Partitioned Removable Media Support. Similar devices should operate correctly, as should other removable media devices that are made available with a supporting ADD device driver. - Iomega SCSI jaz 1GB and 2GB personal hard drives - Iomega Zip ATA 100MB drives (supported only as single partition media). - Iomega Zip ATAPI 100 MB drives - Iomega Zip ATAPI 250 MB drives - Syquest SCSI Syjet 1.5GB portable hard drives - Syquest IDE Syjet 1.5GB portable hard drives - Syquest SparQ IDE portable hard drives 4.2 Large Floppy Removable Media (LS-120 / LS-240) ___________________________________________________ The LS-120 drive supports 120-MB diskettes and is compatible with 3.5 inch 1.44-MB standard diskettes, with improved performance. The LS-240 drive supports 240-MB diskettes, 120-MB diskettes and is also is compatible with 1.44-MB standard diskettes. 4.2.1 Limitations of LS-120 / LS-240 Support o If you have an LS-120 drive as drive B, then you must not format it from an OS/2 windowed or full screen session where the current drive is drive A or drive B. The current drive for an OS/2 windowed or full screen session is given as part of the command prompt. For example, if the command prompt in an OS/2 windowed or full screen session is [C:\], then drive C is the current drive. o If an LS-120 drive is installed in a ThinkPad docking station and a CD-ROM or DVD drive is in the system UltraBay, you may get an error message "A program in this session encountered a problem and cannot continue." when a DOS window is opened. In this case edit the config.sys file and move the statement BASEDEV=IBMIDECD.FLT so that it appears before the statement BASEDEV=IBMATAPI.FLT in the file. o The following devices were tested during the development of the Large Floppy Removable Media Support. Similar devices should operate correctly. - Imation LS-120 - SuperDisk LS-120 - SuperDisk LS-240 4.3 CD-ROM Device Manager (OS2CDROM.DMD) _________________________________________ The CD-ROM Device Manager (OS2CDROM.DMD) has several additional features. These features are described in file ddk_note.txt. This file is included into this IDEDASD package. 4.4 CD-RW Media Support in IBMIDECD.FLT and IBMATAPI.FLT _________________________________________________________ IBMIDECD.FLT and IBMATAPI.FLT now supports IDE CD-Writers for reading and writing. 4.5 Additional Parameters for IBMATAPI.FLT and IBMIDECD.FLT Driver ___________________________________________________________________ PARAMETER FUNCTION /V Verbose Mode, displays filter status on detected and emulated devices. /A:n Specify adapter: 0=primary, 1=secondary, 2=DockingStation primary, 3=DockingStation secondary. /I Ignore adapter n specified by /A:n. Example: "/A:1 /I" secondary IDE channel will not be filtered. /U:n Specify unit: 0=master, 1=slave. /!U:n Specified unit will be ignored. Examples: "/A:1 /!U:1" ignore (not claim) slave unit on secondary IDE channel. "/A:2 /!U:0" ignore (not claim) DockingStation UltraBay. /SCSI Export IDE device as SCSI device. Can be used to emulate SCSI CD-RW device as IDE CD-RW device. Example: "/A:1 /U:0 /SCSI" will report SCSI CD device attached as secondary IDE channel master unit . /TYPES:xxx Specify device types supported by WarmSwap. x can be C=CD (CD-ROM, CD-R, CD-RW, DVD, etc), L=LS (LS-120, LS-240), Z=ZIP Examples: "/A:1 /U:0 /TYPES:CLZ" enable swapping between CD, LS and ZIP "/A:1 /U:0 /TYPES:CZ" enable swapping only between CD and ZIP If certain device is in the UltraBay during Boot it will be enabled for swapping. /C IBMATAPI.FLT and IBMIDECD.FLT have been modified so that they no longer fill the request's Scatter/Gather (S/G) list with 0's for the commands without a data tranfer phase, even if the particular command contains a valid S/G list. To avoid possible unforseen compatibility problems with older drivers, the /C parameter can be used to disables this new behavior. 5 Supported IDE Controllers, Known Restrictions and Limitations _________________________________________________________________ 5.1 Supported Chipset Table ___________________________ The OS/2 IDE Controller Adapter Device Driver (IBM1S506.ADD) supports the following PCI IDE Controllers --------------------------------------------------------------- |Controller| Controller Info | Highest | Comments | | Name | | UDMA | | --------------------------------------------------------------- |CMD640 | First CMD640 | - | | |RZ1000 | First RZ1000 | - | | |I82371FB | INTEL82371FB | - | | |PIIX3 | Intel PIIX3 IDE | - | | |ORION | INTEL_ORION | - | | |PIIX4 | Intel PIIX4 IDE | ATA 33 | | |I82801AA | Intel 82801AA IO HUB | ATA 66 |See sec. 5.2.1 | |I82801AB | Intel 82801AB IO HUB | ATA 33 | | |I82801BA | Intel 82801BA IO HUB | ATA 100 |See sec. 5.2.1 | |I82801CA | Intel 82801CA IO HUB | ATA 100 |See sec. 5.2.1 | |I82801DB | Intel 82801DB IO HUB | ATA 100 |See sec. 5.2.1 | |I82801EB | Intel 82801EB IO HUB | SATA 150 |See sec. 5.4 | |I82801FB | Intel 82801FB IO HUB | SATA 150 |See sec. 5.4 | |I82801FR | Intel 82801FR IO HUB | SATA 150 |See sec. 5.5 | |I82801GB | Intel 82801GB IO HUB | SATA 150 |See sec. 5.4 | |I82801GR | Intel 82801GR IO HUB | SATA 150 |See sec. 5.5 | |CMD646 | CMD 646 PCI to IDE | ATA 33 | | |CMD648 | CMD 648 PCI to IDE | ATA 66 | | |VIA586B | VIA 586B PCI to IDE | ATA 33 |See sec. 5.2.2 | |VIA596B | VIA 596B PCI to IDE | ATA 66 |See sec. 5.2.2 | |VIA686A | VIA 686A PCI to IDE | ATA 66 |See sec. 5.2.2 | |SIS630 | SIS 630 PCI to IDE | ATA 66 |See sec. 5.2.3 | --------------------------------------------------------------- 5.2 Known Restrictions and Limitations ______________________________________ This section covers some restrictions and/or limitation for the IBM1S506.ADD driver. These restrictions are mainly due to hardware problems. DMA for ATAPI devices is disabled by default. The exception to this is ATAPI devices on Intel I82801AA chipset and later Intel chipsets (including all SATA controllers). DMA for the ATAPI device can be enabled manualy by using the "/BM" parameter. (To enable it see sec. 3.8) Example: "/A:1 /U:0 /BM" enables DMA for the Master device attached to the secondary IDE channel. If a device is UDMA capable, using "/BM" parameter is recommended only if the IDE 80 pin flat ribbon cable is used (instead of standard 40 pin flat cable). The IBM xSeries 226 with the optional ServeRaid 6i adapter will not work with the IDE (Parallel and/or Serial ATA) hard drives enabled. When trying to use the ServeRaid adapter with the IDE hard drives enabled simultaneously, a Trap D system error will occur during system boot. This restriction applies to hard drives (HDD) only and does not apply to ATAPI devices (CD, DVD, etc). To avoid this system error either disable the HDD attached IDE controllers, remove the IDE HDD drives from the system or remove the ServerRaid adapter from the system. 5.2.1 Intel Chipsets Limitations ________________________________ o for the 82801AA, 82801BA and 82801BA Mobile chipsets where there are 2 devices on a channel, the fastest UDMA mode will be limited to UDMA 2. o on some systems with 82801DB and later chipsets there is problems with proper 80 pin cable detection. To avoid problems with cable detection use only 80 pin IDE cables. The 80 pin cable are a requirement for devices to operate in UDMA mode and are usually installed in the system when the drive and system support UDMA. If you use 40 pin cable on primary or secondary channel, specify the parameter "/UDMA:2" in CONFIG.SYS for that channel. Usage of this parameter is described above (see sec. 3.8). Examples: use "/A:0 /UDMA:2" if you have a 40 pin cable on the primary channel use "/A:1 /UDMA:2" if you have a 40 pin cable on the secondary channel use "/A:0 /UDMA:2 /A:1 /UDMA:2" if you have a 40 pin cable on both channels o for 82801 series chipsets (including all SATA controllers) DMA is enabled for ATAPI devices by default. It can be disabled using "/!BM" parameter (see sec. 3.8). Example: "/A:1 /U:0 /!BM" disables DMA for Slave device attached to secondary IDE channel. "/A:1 /U:1 /!BM" disables DMA for Slave device attached to secondary IDE channel. 5.2.2 VIA Chipsets Restrictions _______________________________ The IBM1S506.ADD driver has the following limitations for the VIA IDE controllers listed above: o all of the VIA chipsets have a problem with 80 pin cable detection. To avoid problems with cable detection use only 80 pin IDE cables. The 80 pin cable are a requirement for devices to operate in UDMA mode and are usually installed in the system when the drive and system support UDMA. If you use 40 pin cable on primary or secondary channel, specify the parameter "/UDMA:2" in CONFIG.SYS for that channel. Usage of this parameter is described above (see sec. 3.8). Examples: use "/A:0 /UDMA:2" if you have a 40 pin cable on the primary channel use "/A:1 /UDMA:2" if you have a 40 pin cable on the secondary channel use "/A:0 /UDMA:2 /A:1 /UDMA:2" if you have a 40 pin cable on both channels o any VIA chipset, which is not listed above, but has the same PCI Device ID, will be detected as a VIA586B and UDMA performance mode will be limited to UDMA 2 for any device that can operate above UDMA Mode 2. 5.2.3 SiS Chipset Limitations _____________________________ For SiS IDE controllers listed above the following restrictions applies: o If there is a UDMA device on the SiS Secondary channel and an 80 pin ribbon cable is not detected, then the driver will limited the mode to PIO for this channel. o Some systems with SiS chipsets may be unable to boot from a FAT partition if the Hard Drive capacity is larger than 32GB. In this case, you can either boot from an HPFS partition or change your BIOS settings to disable "Block mode" for this drive in the system's setup. 5.3. Chipset Extended Detection Algorithm for Intel Chipsets ____________________________________________________________ The IBM1S506.ADD driver can automatically detect all PCI IDE chipsets described in section 5.1 and enables the highest possible DMA/UDMA modes for all drives. Because Intel's chipsets provide good backward compatibility it is possible to detect a newer chipset and use it as the latest known one. To use this feature, this support must be enabled by the user with a config.sys parameter "/CDA". If this parameter is specified, then Extended Detection Algorithm will be enabled and newer Intel chipset can be detected as the latest chipset described in the supported chipset table (see section 5.1) and higher possible DMA/UDMA modes can be properly detected and enabled for all drives attached to that chipset. If a system hang or trap occurs when this parameter is used, then it should be removed from config.sys and legacy detection mode should be used for that chipset. 5.4. Serial ATA for Intel Chipsets Considerations _________________________________________________ The IBM1S506.ADD driver automatically detects Intel Serial ATA and Parallel ATA controllers described in section 5.1 and enables the highest possible DMA/UDMA modes for all drives. For PATA devices (know also as standard IDE devices or ATA devices) the maximum transfer rate for Intel IDE controllers is ATA100. For SATA devices this is SATA150. For SATA devices parameters /UDMA:n and /!UDMA (see section 3.8 for details) have no effect. SATA devices in DMA mode will always operate in the maximum possible transfer rate. 5.5. Intel 82801FR and 82801GR support in IBM1S506.ADD ______________________________________________________ IBM1S506.ADD driver supports "R" versions of chipsets (82801FR and 82801GR) only in legacy mode if the SATA controller is configured to operate as an IDE controller (in legacy mode) by the system BIOS. If the ICH6R or ICH7R SATA controller is configured to operate as RAID or if AHCI mode is enabled, then the IBM1S506 driver will not detect the SATA controller. The IBM1S506 driver does not support any RAID functionality and the IBM1S506 does not support SATA controllers in AHCI mode. 6 Copyright and Trademark Information ________________________________________ The following terms are trademarks of International Business Machines Corporation in the United States and/or other countries: IBM OS/2 ThinkPad Ultrabay Warp Warp Server Warp Server for e-business Other company, product, and service names may be trademarks or service marks of others. THE INFORMATION PROVIDED IN THIS README IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. (C) Copyright IBM Corporation, 2001, 2005. All rights reserved. U.S. Government Users Restricted Rights -- Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.