Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Pete

Pages: 1 ... 3 4 [5] 6 7 ... 87
61
Hi Andrew

To try to ascertain where the boot gets stuck: During boot press Alt-F2 when the "OS/2" appears in top left corner of screen. This should show drivers loading and either the driver displayed or the next driver that should load is the likely cause of boot failure.

Having established where boot stops Boot the install media to the Installer gui and select System Management(? think that is what it is called) instead of starting a fresh install. You can then use Text Editor to open old and new config.sys files to compare and adjust as necessary.


Regards

Pete



62
Networking / Re: arcmapper
« on: November 15, 2023, 07:43:31 pm »
Hi Rick

I don't use samba or arcmapper myself but you could try deleting the CONNECTIONS  from the config.sys SET AUTOSTART line to see if that solves the problem.


Regards

Pete

63
Applications / Re: HyperAccess 7
« on: November 15, 2023, 07:38:51 pm »
Hi cristech

Looks like the install fails as the installer finds a lack of disk space - How much does it report in the install failed message?


Regards

Pete



64
Applications / Re: XWP v1.0.16
« on: November 12, 2023, 04:37:55 pm »
Hi All

Playing with the new Text Size - was on Standard - I selected Medium size, clicked Test and was a bit surprised to see the Properties notebook shrink in size. Is that supposed to happen?


Regards

Pete



65
Multimedia / Re: VLC - does it play disks?
« on: November 12, 2023, 04:27:32 pm »
Hi All

Probably 1 of the best sites providing "fixes Out There In Naughty Land"  https://tdb.rpc1.org/

I must admit to having successfully used their firmware variants on many DVDRWs in the past  :-)


Regards

Pete

66
Setup & Installation / Re: ArcaOS 5.1
« on: November 12, 2023, 02:49:47 am »
Hi Rick

Possibly something related to early os/2 messaging software, see http://annex.retroarchive.org/cdrom/smsw-modmad-2/MAXIMUS/index.html and scroll down to sqpck141.zip which contains the dll file of that name.

Whether it is related...


Regards

Pete


67
Setup & Installation / Re: ArcaOS Sluggishness
« on: November 12, 2023, 02:43:03 am »
Hi Dariusz

What I would expect to happen if AHCI support is turned off in the BIOS is that the AHCI.ADD driver will not load (no controller hardware) and my SATA DVDRW, which uses AHCI, will not work (read/write).

Here the BIOS options for SATA are
1] AHCI
2] RAID
No, no (E)IDE/PATA option.


I guess you must be accessing SSDs as EIDE(PATA) using dansi506.add?

AHCI is a little faster than EIDE(PATA) - and NVMe is faster than AHCI  :-)

I am turning off AHCI support for the SATA1 connected SSD because:
1 ]something, seems to be gpt.flt, gets a bit freaked out by that drive - Windows11 install on it - which doubles boot time
2] I have absolutely no need/want to access the Windows11 installation on that drive from ArcaOS

I have not seen any problems with AHCI myself on various systems that I have used it on, was happily using it on this system with an SSD and a "spinner" as well as a DVDRW until I purchased an NVMe drive.

Ouch! Just got prodded by wife who reminds me that a few years ago I had a system that was "misbehaving" with weird, occasional system freezes. I thought a drive was dying and enlisted the help of Jan (DFSee) to try to ascertain which of the 4 disks fitted was having a problem. After looking through the logs he advised me to check my PSU, power and data leads. Testing the PSU output revealed fluctuating voltages, opening the PSU and seeing a few "overcooked" bits explained a lot.

I think in your position I would check SATA leads, power and data, are connected properly and that the PSU is clean and outputting correct, consistent voltages etc, also worth checking system fans are clean(ish). Although if this all works fine with danis506.add there should not be a problem...

Out of interest:
 What hardware is involved? ie mainboard/chipset(s), SSDs
 What config.sys line would you be using for AHCI support


Regards

Pete





68
Hardware / Re: Using a UPS to save SSDs
« on: November 07, 2023, 08:24:59 pm »
Hi Andrew

The printer will sit at the far end of a 5m USB-2 cable...

No Wireless capability?
If printer and router are both wireless capable it gives you more options on where to site the printer - and there is no need to go tripping over long USB leads  :-)


Regards

Pete

69
Applications / Re: VLC 3.0.19 don't install !
« on: November 07, 2023, 01:51:34 am »
Hi Dave

Martin is probably not starting it "with a weird location".

Martin has probably done the same as me - unzipped to his choice of location keeping the vlc/2 directory tree. In which case the libpath entry is needed for vlc2\usr\local\bin\vlc.exe to find it's support libs.


Regards

Pete




70
Setup & Installation / Re: UEFI: Dual Boot - Windows 11 and ArcaOS 5.1
« on: November 03, 2023, 12:16:05 am »
Hi Rich

Thanks for your explanations re the incorrect boot list descriptions.

Presuming bootdelete works as well as bootorder - Yes, had a quick "play" - the only missing bootlist utility is the bootadd you mention you did not get around to writing before leaving AN.
Any plans to complete your bootlist utilities? :-)

Yes, sorry, probably not the only person to mix up the terms... I thought I'd seen something in the AN docs or wiki... Which led me to suggest the menuentry using OS2LDR.EFI with desired boot drive as the option. Pleased to read that it should work although with text mode problems.


Regards

Pete



71
Setup & Installation / Re: UEFI: Dual Boot - Windows 11 and ArcaOS 5.1
« on: November 02, 2023, 07:25:45 pm »
Hi All

I seem to recall something about being able to boot both GPT and MBR volumes on the same disk somewhere in the ArcaOS 5.1.0 related docs but have not been able to find it again to check exactly what was stated.

I am wondering what exactly os2ldr.efi does... something to prepare ArcaOS to boot I guess.
Does that end up with starting \os2ldr on the ArcaOS boot drive?

If "Yes" maybe this will work for Neil

menuentry "ArcaOS-H" {
    icon /EFI/BOOT/icons/os_arcaos.png
    loader \EFI\OS2\OS2LDR.EFI
    options "H:"
}


Regards

Pete

72
Setup & Installation / Re: UEFI: Dual Boot - Windows 11 and ArcaOS 5.1
« on: November 02, 2023, 07:09:35 pm »
Hi Dave

Well, using the UEFI shell looks like fun but could be the answer to a couple of incorrect descriptions - not sure how - in the boot list:

a] AN Launcher shows as UEFI-OS
b] rEFInd shows as Windows Boot Manager
(Note: the 2 Windows 11 installations also show the name of the disk they are installed to ie Netarac SSD or Crucial P3, so I know which of the 3 Windows Managers is which)

So, the plan was to delete those (a] and b]) entries then add them back to the boot list with the correct descriptions.

My mainboard BIOS did have an option for booting a UEFIShell but that seems to have disappeared...

Downloaded the ShellBinPkg.zip linked into the rEFInd UEFI install instructions and put a copy of shell_x64.efi into \EFI\Boot

Then I used miniLVM, aka Logical Volume Manager (Simple), to re-install AN Launcher as that would pick up the shell_64.efi and offer it as a boot option.
On reboot started AN Launcher and selected shell_x64.efi.

Oh, What Fun!!! - Find the correct fs*: where "*" represents a number
fs0: was the ESP on the SATA drive so changed to fs1: without any problem but issuing ls resulted in system hang
Issuing ls on fs2: caused the same system hang
fs3: turned out to be the correct (NVMe) ESP.

Followed the rEFInd UEFI install instructions steps 12 to 15 to:

1] use bcfg dump -b to get the list of NVRAM entries
2] delete a] and b] entries above.
3] add the rEFInd entry
4] move the rEFInd entry to the top of the boot list

As I had already (re)installed AN Launcher it now had an entry with the correct name so no further action required for that.

Result: Checking BIOS on reboot rEFInd is the 1st entry, AN Launcher is correctly listed and the unwanted entries (a] and b] above) are now gone.

Exited BIOS and rEFInd appeared onscreen.

So, all worked well but it would still be easier to make those NVRAM changes from a nice little ui in ArcaOS.


Regards

Pete

73
Setup & Installation / Re: ArcaOS Sluggishness
« on: November 02, 2023, 02:43:34 am »
Hi Rich

Not over stressed about the boot time - just surprised.

SATA is set as AHCI in the BIOS.
Windows 11 boots in under 20 secs from this SSD so I guess GPT.FLT does not like something about the SSD.

I only had the SATA disk visible to ArcaOS while fannying around getting rEFInd working and it is now "ignored" on the config.sys line
     BASEDEV=OS2AHCI.ADD /A:0 /P:0 /I

Back to fast booting  :-)


Regards

Pete





74
Setup & Installation / Re: UEFI: Dual Boot - Windows 11 and ArcaOS 5.1
« on: November 01, 2023, 03:17:59 pm »
Hi Dave

Not Changing BIOS boot order- Adding to the BIOS boot list.

As AN Launcher adds itself to the BIOS boot list I guess what we need is the code that is used to do that made into a simple utility app that could add other bootable *.efi files (boot managers) to the BIOS boot list rather than booting an alternative OS (Windows) to do the job.


Regards

Pete





75
Setup & Installation / Re: UEFI: Dual Boot - Windows 11 and ArcaOS 5.1
« on: November 01, 2023, 05:32:02 am »
Hi Dave

No install script used here, simply unzipped and followed manual install instructions - Basically copy the refind dir to ESP:/EFI/refind and then delete the unneeded bits in my case leaving

Y:\EFI\REFIND>dir

Volume in drive Y has no label.
The Volume Serial Number is E0F8:0378.
Directory of Y:\EFI\refind

29-10-23   1:35a     <DIR>           0  .
29-10-23   1:35a     <DIR>           0  ..
29-10-23   1:36a     <DIR>           0  icons
29-10-23  12:51p     <DIR>           0  tools_x64
 1-11-23   4:05a     <DIR>           0  vars
 1-11-23   4:03a     36100           0  refind.conf
 6-03-23  11:04p    266936           0  refind_x64.efi
        7 file(s)     303036 bytes used
                    65771520 bytes free

vars directory was created by rEFInd.

Of course, the problem with installing on ArcaOS is that there does not seem to be a way to add rEFInd to the BIOS boot list - unless anyone knows differently?

I did copy refind.efi and the conf file into /EFI/Boot as I thought that was where they needed to be put, but looking back at how I added refind to the BIOS boot list shows why the refind files in /EFI/Boot are not used:-

bcdedit /set "{bootmgr}" path \EFI\refind\refind_x64.efi

The above windows command adds the EFI\refind\refind_x64.efi to the boot order...


Regards

Pete








Pages: 1 ... 3 4 [5] 6 7 ... 87