Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Remy

Pages: [1] 2 3 ... 40
1
Web applications / Re: Dooble releases, Qt5 builds
« on: May 24, 2023, 02:21:31 pm »
Something doesn't work well.... webengine or dooble !
After unpredictable time or downloaded datas, network goes unresponsive after a drop of speed with high cpu or possible freeze !
I don't know how to trap this kind of problem.
Resolving this could make dooble very great ...   

2
Networking / Re: Changing subnet on network
« on: May 23, 2023, 07:21:16 pm »
Hi,

You can use tcpcfg2 to update your lan interface having defined dhcp server ip@
or without specifying ip@, you can start dhcp client (default arcaos i think)
Usage: dhcpstrt [ -d maxwait] [-i lan<#>]
  Starts DHCP client & waits for it to setup ip address.
  Maxwait is the time in seconds rounded to 5 seconds.
  If not specified, the interval defaults to 45 seconds.
  lan<#> specifies the interface requiring dhcp configuration.

e.g. dhcpstrt -i lan0 -d 0

review your \mptn\bin\setup.cmd

3
Web applications / Re: Dooble releases, Qt5 builds
« on: May 20, 2023, 09:55:46 am »
The latest build seems to be the best (fast page load ...)
But issues here https://www.nperf.com  (slow process)  as exemple

Regards

4
Applications / Re: Upplay QT5
« on: May 19, 2023, 12:40:40 am »
Could no one create an OS/2 build ? (QT5 - please)
https://framagit.org/medoc92/upplay

5
One solution, I think should work

Have a NAS server connected to a internet box or having internet connection possible
ex: Synology NAS + DSM interface   (I have a 703+)

Install/customize the VPN PPTP server with No MPPE   (Injoy VPN client allow PPTP connection without encryption 'MPPE")
Dynamic ip@ e.g. 10.0.0.0
....
Authentification MS-CHAP v2
Manual DNS (e.g. your internet box ip@)

Define autorized users with needed access under the NAS.
Once done, the VNP client using PPTP + userid + password should be able to establish a connection  after updating the internet box routing table

On you internet box open needed ports from from internet to your NAS ip@ to access the VPN server
Under VPN client, define the VPN server ip@ seen from internet and use PPTP as well + userid + password

I could not give it a test but I used similar configuration with windows (PPTP) and Injoy allows PPTP VPN (no encryption)
Not easy and of course, no supported encryption (MPPE)

6
Setup & Installation / Re: ArcaOS and Storage - Discussion
« on: April 19, 2023, 01:49:18 pm »
Hi Eugene,

I read the post and could not determine if you plugged your disk into one of the M.2 slot or on SATA port ?
I have a board under which, M.2 is not usable - PCI.e and had to remove the disk to see all other - , my ArcaOs has to be installed on a SSD sata port

(note: my board is a intel one...)
My be you can try exclude M.2 disks from under your config.sys AHCI driver and use disk plugged into SATA port to check if installation can proceed. This could help into problem determination 
   

7
Utilities / Re: Extract *.img file
« on: April 16, 2023, 09:19:19 pm »
rename the file to .iso and then, try to mount the iso file (if not compressed, it could work)

8
General Discussion / Re: PMfax
« on: March 28, 2023, 04:00:00 pm »
Help :'(. I have lost module imgfx6mn.dll required by PMfax. Is there anybody who has a copy and could send it to me?

I just started my older PMFax to review logs and it start without the need of the dll !

I suppose imgfx6mn is from ImageMAKER provided by your fax device drivers.
Check if you have your fax card drivers. 

9
Applications / Re: Java applications
« on: March 22, 2023, 04:15:48 pm »
Quote from: Martin Iturbide

Hi Martin, I sent you a private message (PM) about an archived no more used program I have.
If it will interest you.
Regards

10
General Discussion / Re: PMfax
« on: March 22, 2023, 04:09:40 pm »
May be it is installed by pmfax !
Did you try to install again pmfax ?
https://hobbes.nmsu.edu/?detail=%2Fpub%2Fos2%2Fapps%2Fcomm%2Ffax%2FPMFaxPro_upd_3-2.zip

11
Applications / Re: AVxCAT (v2 into test)
« on: March 15, 2023, 10:24:30 am »
https://remydodin.levillage.org/en/realisations.php?item=6900&id=realisations

(Official GA on 2.0.0.4 including new pdf revision file)

12
Please, read they warning message :

WARNING

This browser does not run well on winxp SP2 and lower. If you do not want to install SP3, be ready for crashes and blue screens. If you are on SP2 and lower, there is no need to post a screenshot from blue_screen_view. And i suggest to apply postready updates of 2019.


13
Applications / Re: AVxCAT (v2 into test)
« on: March 07, 2023, 06:47:49 pm »
For current V2 ->  now V2.0.0.4
A few corrections ( e.g.  regression on metadatas when grabbing CD code introduced on 25 feb 2023)   

avxcat_rep.zip (for the V2  exe replacement only)
https://remydodin.levillage.org/doc/realisations/downloads/avxcat_rep.zip

AVXCAT_S-2_0_0_4.wpi
https://remydodin.levillage.org/doc/realisations/downloads/AVXCAT_S-2_0_0_4.wpi

14
Hi

Probably got a sys0039 due to a lack of usb floppy drive.

Regards

Pete

But why not the SYS0021 !

15
I'm curious to know why you've got a SYS0039 not ready message (for COMn !) instead the more expected SYS0021 not ready message ?

Pages: [1] 2 3 ... 40