Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Per E. Johannessen

Pages: [1] 2 3 ... 18
1
Setup & Installation / Re: Switch from CSM to UEFI
« on: October 31, 2024, 06:14:11 pm »
Thanks to all for info, I haven't decided what "route" to take yet but will report when done.
The MBR-to-GPT converter developed by Rich would be a great tool to have, and I would not expect it to be freeware.
Hope that AN can imagine a use for it now. (USD 2500 is a bit too much for my budget, although I'd happily pay a reasonable fee for a user license.)

2
Setup & Installation / Re: Switch from CSM to UEFI
« on: October 30, 2024, 05:40:33 pm »
Interesting. Could the MBR-to-GPT converter be used on a win10-disk/NTFS  as well?
(I have so far not assigned any drive letter/LVM info for that disk.)

3
Setup & Installation / Re: Switch from CSM to UEFI
« on: October 29, 2024, 02:01:12 am »
I have Win10 but since it's been run with CSM it has not created any ESP partition. AFAIK updating Win10 to Win11 requires UEFI so I assume that the updating process will create the ESP partition, (the Win10-disk has enough free space).
Before updating to Win11 I think I will disconnect the AOS-disk and only have the win-disk and another empty disk in the system.
If the win updating goes well I'll install latest AOS to the empty disk.

Finally I plan to re-connect the older AOS disk and wonder if there is something I have to do manually or will it be seen automatically and added to whatever boot manager AOS 5.1 sets up?

The graphics card is a Radeon RX 7800 XT and I have no idea about the size of the frame buffer or where it is put.
 
I have checked https://www.arcanoae.com/wiki/ and the info is good for a new installation however I initially had a hope of "converting" an existing AOS installation to UEFI. Couldn't find any info for that scenario so I'll go for a new 5.1 installation.

4
Setup & Installation / Re: Switch from CSM to UEFI
« on: October 28, 2024, 09:27:13 pm »
Agree with the "if isn't broken etc." but I have to replace the graphics card and the new one I got needs UEFI.

5
Setup & Installation / Switch from CSM to UEFI
« on: October 28, 2024, 05:22:56 pm »
I have a system with AOS 5.0.4 and Win10 installed on separate disks, (using AirBoot, CSM).
Does anyone have a "step by step" for how to switch from CSM to UEFI ?


6
Programming / Re: Start program from VX-Rexx
« on: March 27, 2024, 11:24:55 pm »
Thanks to Dave Yeo, who built version 4.01, the new pdftotext now works from VX-Rexx as well.

7
Programming / Re: Xpdf v. 4.01
« on: March 27, 2024, 10:37:14 pm »
Thanks a lot, Dave.

I've only tried pdftotext so far. This version also seems to work fine from VX-Rexx.

8
Programming / Xpdf v. 4.05
« on: March 27, 2024, 08:04:21 pm »
Noticed this post;

https://www.os2world.com/forum/index.php?topic=2162.0

Does anymone know if the v. 4.05 cmdline tools for OS/2 are available anywhere?

9
Programming / Re: Start program from VX-Rexx
« on: March 25, 2024, 04:14:54 pm »
Now I've also tested running the command below from DBExpert;

address cmd "start /C /min P:\test\pdftotext.exe source.PDF input.txt"

At one point it actually worked and produced a nice input.txt, actually the best so far since it
handled the special character 'ΓΈ' correctly.
Funny thing is that it worked only one time.
Have tried lots of times and don't even get any error messages.

10
Programming / Re: Start program from VX-Rexx
« on: March 24, 2024, 12:23:54 am »
When running a cmd-file with only the line below it works ok.
address cmd "start /C /min P:\test\pdftotext.exe source.PDF input.txt"

I've tested a few other programs from VX-Rexx using "address cmd" and they work.

pdftotext.exe is in the same directory as the VX-Rexx project and the cmd-file.

I've also copied the cmd-file and pdftotext.exe other directiories and it still works so I assume it
does not depend on any other dll.

11
Programming / Re: Start program from VX-Rexx
« on: March 23, 2024, 02:48:49 pm »
Thanks, but I can't get any of the suggestions to work.

ADDRESS CMD "P:\test\pdftotext.exe source.PDF input.txt"
Results in "private_alloc failed, error code = 0x00000137

'@start cmd /c start "pdftotext" /b/k '||your_program
Results in "invalid expression"

In another project this is working fine:
address cmd.exe "start /C /min d:\gs\GS9.15\BIN\gsos2


12
Programming / Start program from VX-Rexx
« on: March 22, 2024, 09:54:21 pm »
Hi,

I have a cmd file with this line;

address cmd.exe "start /C /min P:\test\pdftotext.exe source.PDF input.txt"

and it works fine (converting the pdf to txt).

Trying to run the same line in VX-Rexx is not working.

Got some good tips in the below thread:

https://www.os2world.com/forum/index.php/topic,2932.msg32804.html#msg32804

I've tried any "combination" I could think of but no success.
At one point I got the error message "private_alloc failed, error code = 0x00000137".

Anyone who knows how to get it to work in VX-Rexx?

13
Applications / Re: PMMail
« on: February 24, 2024, 12:59:21 am »
Still works here, also the link Martin provided.

You can sponsor through this link:
https://www.arcanoae.com/shop/voice-sponsoring/

14
Applications / Re: PMMail
« on: February 23, 2024, 11:02:59 pm »
http://www.os2voice.org/ seems to load fine now, (Firefox 45.9.0).

15
Setup & Installation / Re: DB2 v. 6.1 / Java
« on: February 23, 2024, 05:08:34 pm »
Well, I downloaded and installed 1.1.8 and DB2 Control Center works.
Problem now is that DB2 Administration Server will not start, SQLSTATE=57019.

Alex, you're right, the runtime was already installed in x:\OS2\JRE\Java11  ???

Neil, when trying to create a database I can select "local" and it is not asking for any protocol.
(Since the Adm Server won't start I'm unable to complete the steps for creating a new database,
will keep File and Print in mind.)

Pages: [1] 2 3 ... 18