Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - David McKenna

Pages: [1] 2 3 ... 16
1
Applications / Re: Cumulus weather software for OS/2
« on: May 16, 2020, 03:09:57 pm »
 It appears this software is available on Hobbes... search wcalcos2.zip.

2
Multimedia / Re: Updated Uniaud32 build
« on: May 15, 2020, 12:35:44 pm »
 Hi Paul,

  Looks like you've been busy! I tried all 3 and it is a mixed bag:

Linux 3.2: Can't boot, get the 'Not enough memory...' message described earlier
Linux 3.2.102: Can't boot, ends with a 'System detected an internal processing error....' type message.
Linux 3.5: Seems to work fine (system sounds and YouTube)

 I'll attach a debug log for 3.5. Thanks again!

3
Multimedia / Re: Updated Uniaud32 build
« on: May 13, 2020, 11:18:51 pm »
Hey Paul,

  Tried 'lxlite uniaud32.sys' on both the debug and release versions of 3.1.9 and it made them much smaller, but both still result in 'Not enough memory...' at boot. I am now running the new official version released at http:\\trac.netlabs.org\uniaud (20200506.exe) with no trouble...

Regards,

4
Multimedia / Re: Updated Uniaud32 build
« on: May 13, 2020, 10:41:06 pm »
Pete,

 System case is fine, the official UniAud works fine, and Paul's builds before 3.1.9 work fine. I'll upload a 'testlog generic' in case anyone is interested. Must be something else...

Regards,

5
Multimedia / Re: Updated Uniaud32 build
« on: May 13, 2020, 01:03:55 pm »
 OS4User - Tried decreasing VAL in increments of 512 down to 1024, but always the same result - 'Not enough memory...'.

Regards,

6
Multimedia / Re: Updated Uniaud32 build
« on: May 13, 2020, 12:16:40 pm »
Paul,

  Can't get the computer to boot with either the debug or release version of 3.1.9 - after the disk check there is a long pause, then a bunch of messages flash by and end with 'Not enough memory to run PMShell.exe on the Protshell = statement in Config.sys' (I have 8GB). Never saw that before!

Regards,


7
Multimedia / Re: Updated Uniaud32 build
« on: May 10, 2020, 09:07:06 pm »
Paul,

  No sound with this one either - debug log attached...

Regards,

8
Multimedia / Re: Updated Uniaud32 build
« on: May 10, 2020, 05:12:19 am »
Hi Pete,

  Good point to check the mixer settings. I notice a couple of additional settings in my Linux 3.2 mixer as well (compared to earlier ones) - expanded support in that version for my sound chip maybe? Master Playback and Master Switch are set the same in all the ones tried though, so something else is going on with Linux 3.2 here...

Regards,

9
Multimedia / Re: Updated Uniaud32 build
« on: May 09, 2020, 02:10:07 pm »
Paul,

  I gave the Linux 3.1 version a shot and it seems to work fine... I'll upload the debug alsahlp$ for it in case it's interesting...

Regards,

10
Multimedia / Re: Updated Uniaud32 build
« on: May 08, 2020, 10:00:22 pm »
Paul,

 FYI - I tried VLC with the Linux 3.2 driver, but still no sound. No errors at boot though, and it shows up in the hardware manager...

Regards,

11
Multimedia / Re: Updated Uniaud32 build
« on: May 07, 2020, 10:07:44 pm »
 Hi Paul,

  Both the trunk and Linux 3.0 work fine here, but no sound with Linux 3.2. I'll attach the debug alsahlp$. Thanks for tackling Uniaud again!

Regards,

12
General Discussion / Re: ArcaOS User Accounts
« on: April 06, 2020, 10:20:46 pm »
 I have my laptop setup to ask a password at POST... setup thru the BIOS. But if you don't want to do that, with ArcaOS you can right click on the desktop, choose 'Properties', then click on the 'Screen Saver' tab. Check 'Screen Saver Enabled',,'Use Password Protection', enter your password, and check 'Start Screen saver on system startup'. This will boot the computer to the screen saver, and require a password to turn it off.

Regards,

13
Hardware / Re: PCIe - SATA3 card choices?
« on: April 06, 2020, 12:52:37 am »
 Dariusz,

 I was surprised to get better performance by turning off NCQ when I did it, so who knows?... might as well try different 'Link Speed' settings and see if anything crops up...

Regards,

14
Games / Re: Quarantine Gaming !! - Dev/Port Help
« on: April 06, 2020, 12:41:28 am »
Hi Tellie,

  You have 3 DLL's that I do not have: SDLImage.dll, SDL_i120.dll and SDL_t200.dll. If you move those out of the libpath, do you still have sound? I tried installing the SDL-devel package with YUM, but it didn't help. I notice the dates on your files are newer too - do you remember where you got the SDL package from?

Regards,

15
Games / Re: Quarantine Gaming !! - Dev/Port Help
« on: April 05, 2020, 04:19:30 pm »
 No sound here either - my startup window is identical to Martin's. The docs installed by the YUM version of SDL imply there are other modules not supplied (only SDL and SDL_ttf are):

  SDL v. 1.2.15
  SDL_ttf v. 2.0.10
  SDL_image v. 1.2.12
  SDL_mixer v. 1.2.12
  SDL_net v. 1.2.8
  SDL_sound v. 1.0.3

 I wonder if this archive of SDL is incomplete? Have an older version by Digi that does contain those modules, but they don't work with this version of atris (it wants sdl120.dll). Tellie, do you have any of these other SDL DLL's on your system?

Pages: [1] 2 3 ... 16