Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - espenbo

Pages: [1]
1
Setup & Installation / Re: ecom 1.2 hang when booting
« on: 2008.09.22, 19:18:50 »
I have now gotten IP and IPX working so I can connet to my netware servers  :)

I had to do a lot of googling but with the help from hobbs and a  howto there on the subject I got it working with the ODI2NDI.0S2 driver.
Quote
I've made a quick search on hobbes but don't find the howto. Would you please give me the filename or explain the steps you have to do?
I
Yes I shall trye. the hobbs file is here: http://hobbes.nmsu.edu/h-browse.php?dir=/pub/os2/util/network/netware/ntwrtcp.zip

I tride first the odi setup.  Removd my network card from os/2 setyp. And following the setup of netcfg.isa, autoexec.isa and protocol.isa. Just renamed the SMC8000 driver file that was just there with my 3c90x driver.
Thise workt for a ipx only net. By I wanted ipx and ip.

So I tride tcpnet.txt setup. There you have a working os/2 networksetup with ip.
Then you install the netware client. But when it asks for the networkdriver you give 'c:\IBMCOM\PROTOCOL\ODI2NDI.OS2' then when the network setup is finish you make a net.cfg file.

my net.cfg:
LINK Support
LINK DRIVER 3C90X
        FRAME ETHERNET_802.3
        FRAME ETHERNET_802.2
        FRAME ETHERNET_ii
        FRAME ETHERNET_snap
        PROTOCOL IPX 0 ETHERNET_802.3
        PROTOCOL IPX E0 ETHERNET_802.2
        PROTOCOL IP 800 ETHERNET_II
        PROTOCOL ARP 806 ETHERNET_II
        PROTOCOL RARP 8035 ETHERNET_II
Protocol odinsup
        bind 3c90x
Protocol Stack IPX
        bind 3c90x
Protocol TCPIP
        bind 3c90x
        ip_address 192.168.0.14
        ip_router 192.168.0.4
        tcp_sockets 8
        udp_sockets 8
        raw_sockets 1

Thise is with a set ip adress and gatway. Havent tride with dhcpclient yet.

Start up the os/2 network setup program and select the 'Netware Requester' from protocol. Dobbel  click on it and go true the setup. You must setup the the network card adress. I didt not now it. So i found that if you  install IEEE 802.2 and look at a log file for network on bootup you will find it. Sorry can't rember where it is or the name.

Hope it helps.

I alsow installd nwadmin tools for OS/2. The work. But a bit slow....

Quote
- Now I use Norton commander/Midnigth commander to copy/move/edit files, what do I use under os/2?
- VNC client
File commander - LarsenCommander, FM/2 (GUI), FC2 (? CLI)
VNC - pmvnc103_ow.zip on hobbes
[/quote]
I shall trie them.


I'm woundering. I don't think the system is very fast.
Rigth now I have telned server, timed,  novell client, nwadmin,  4os2 windows, text editor, programfiles, mIRC, command promt window and IBM Web browser.

Where do I look for optimasing? And is there a good 'About thise computer' program? Better than
'Hardware manager'

Thanks
Espen

2
Setup & Installation / Re: ecom 1.2 hang when booting
« on: 2008.09.20, 22:35:51 »
Hello

Well I got the computer booting agen, using 'Alt-F1' and removing the problem spot in config.sys

I have now gotten IP and IPX working so I can connet to my netware servers  :)

I had to do a lot of googling but with the help from hobbs and a  howto there on the subject I got it working with the ODI2NDI.0S2 driver.

But now I wounder what files and programs I should hunt down and install.
- I would like to use thise computer as a dos games computer so I need som help optimasing it.
- Manage my netware 4.2 server and 6.5 server.
- Manage my linux server so i need ssh client
- Now I use Norton commander/Midnigth commander to copy/move/edit files, what do I use under os/2?
- VNC client
- More programs that are fun to test?

Thanks
Espen

3
Setup & Installation / ecom 1.2 hang when booting
« on: 2008.09.17, 22:33:43 »
Hello

I´m trying to install netware client to my eCom 1.2.
But now the computer hangs when 3com 3c90x driver is loaded.
error messages: Frame YS0318: MESSAGE FILE MSM:MSG CANNOT BE FON3com 3C90X Etherlink PCI Adapter
3C90X !!-os/2-LSL support moules not installed.


But I can´t get pasted it.
What should I press for getting the computer up agen? looking for something like "F8" under DOS.

Thanks
Espen

4
Applications / Re: Must have programs for new install
« on: 2008.02.24, 02:15:53 »
Hello

Thanks for all the help.
I have found lots of good programs, and the tips was good.

Now, i'm trying to get my samba to work. From the base install of eComStation 1.2R I find my samba shares. but I can't copy the files or read them. And it only works to se the files when i use the 'sharing and connecting' program mount the share from there.
When I trye to use the 'file and print' browser I can see the computers, and the shares on the computer. But when I click on it I get 'No objects were found that matched the specified find criteria'
The samba server is running on linux and is samba 3.0.25b.
It works on mac and linux clients

where do I begin to look for solusens?

Espen

5
Applications / Re: Must have programs for new install
« on: 2008.02.22, 00:22:01 »
Thanks. Every thing helps. But hobbs was to big when you don't now what your lokking for.
Now I can search and download :)

Espen

6
Applications / Must have programs for new install
« on: 2008.02.21, 23:44:48 »
Hello

I have just bougth eComStation 1.2R.
But I have never been a OS/2 user. So I wounder if you could give me a list of must have programs. With name, and what they do.

I have installd:
seamokey
warpin
libc 0.5.1
pixel

Thanks
Espen

Pages: [1]