EXPLANATION OF HPFS386 INTERNAL ERRORS

From OS2World.Com Wiki
Jump to navigation Jump to search

Introduction

When the LAN Manager version 2.00 installable file system (HPFS386) encounters unrecoverable errors, it stops the system and displays the error on the screen using the following format:

Internal processing error
At location #01F0:0892
HPFS Fatal Internal Error #xx

The following is a list of the fatal internal errors HPFS386 may display, along with a brief explanation and possible courses of action for correcting the problem:

Internal Error #0

Explanation

The disk driver routine returned to an HPFS interrupt handler an invalid command.

Action

If you are using standard devices (for example, hard disks that have a proven history under OS/2), the most likely cause is corrupted memory (perhaps caused by some other errant driver). If you are using an unusual device, the problem may be in the device driver supplied by the device manufacturer.

Internal Error #1

Explanation

The file system was unable to allocate a new directory block. Allocation (and deallocation) of directory blocks may be caused by something as simple as renaming a file. When a new directory block is needed, HPFS first tries to allocate it from the band on the disk dedicated to directory blocks. If that fails (either because no more sectors are available or an error occurred accessing the disk), HPFS attempts to allocate the directory block from another intelligent location on the disk. This error is issued only when all attempts to allocate a directory block have failed.

Action

This error can be caused by a full disk. If the disk is not full, the error may be symptomatic of a disk failure. Run Chkdsk /F against the disk to reset the hotfix sector and correct any problems that may exist. If the problem still occurs (or if Chkdsk cannot complete), try replacing the disk drive and related hardware (for example, the controller).

Internal Error #3

Explanation

A failure occurred reading the hotfix sector. During the process of a hot fix (that is, the dynamic replacement of a bad sector with a good sector in the allocation of a file), HPFS reads the one sector bitmap describing which sectors have been reserved for dynamic replacement (that is, hotfix sectors). An error was returned to HPFS when it attempted to read this hotfix sector.

Action

This error can occur only after a failure to read or write another sector on the disk; therefore, it is likely caused by disk drive or hardware problems. HPFS cannot recover if the sector containing the hotfix bitmap goes bad. Run Chkdsk /F to try to recover the volume. If the problem still occurs (or if Chkdsk cannot complete), try replacing the disk drive and related hardware (for example, the controller).

Internal Error #4

Explanation

A failure occurred writing the hotfix sector. See the previous explanation for additional details.

Action

See previous action for recommended steps.

Internal Error #5

Explanation

Failure to allocate storage for the DBCS portion of the codepage. During initialization, HPFS fetches the codepage(s) in use by OS/2 and builds a translation table. The first part of the translation table is placed into preallocated storage. However, storage is allocated to hold the DBCS portion (since it may not exist). HPFS failed to obtain the storage necessary to hold this portion of the codepage.

Action

This is a general system error and does not indicate any problems with the disk drive or its related hardware. If the problem can be is re-created, you should notify a Microsoft Product Support representative for the appropriate product (for example, OS/2, LAN Manager).

Internal Error #7

Explanation

A hotfix attempt was made during HPFS shutdown. During normal processing, HPFS attempts to recover from bad sectors by hotfixing the data to a good sector (see explanation under error number 3). However, during shutdown, HPFS cannot employ hotfixes to recover. This error indicates that a bad sector was discovered during shutdown and HPFS cannot recover.

Action

As with other errors that can indicate disk drive or hardware problems, run Chkdsk /F against the drive. If the problem still occurs (or if Chkdsk cannot complete), try replacing the disk drive and related hardware (for example, the controller).

Internal Error #8

Explanation

The main file system driver (FSD) was unable to open a file that had been opened by the minimal function file system driver (mini-FSD) used during boot time. When an installable file system installs, control is given to a mini-FSD. This mini-FSD is used to mount volumes and open files used during the early stages of the boot process. In the later stages, the full-function FSD is given control. To maintain the same image as the mini-FSD, all volumes mounted or files opened by the mini-FSD must be mounted or opened by the full function FSD. This error indicates that a failure occurred while opening a file that had been opened by the mini-FSD.

Action

This error does not normally imply a failure with the disk drive or its related hardware. However, you may want to try running Chkdsk /F against the drive. If Chkdsk cannot complete, try replacing the disk drive or its related hardware (for example, the controller). If Chkdsk does complete and the problem recurs, this may indicate a problem in either the device driver or HPFS. Contact a Microsoft Product Support representative for the appropriate product (for example, OS/2, LAN Manager) for additional assistance.

Internal Error #9

Explanation

HPFS has exhausted its supply of hotfix sectors. Each time HPFS detects a bad sector, it reassociates the data with a good sector (that is, it hotfixes the problem). A fixed quantity of hotfix sectors are preallocated when the device is formatted and a bitmap is created that records which hotfix sectors are available. This error indicates that all of the hotfix sectors that were preallocated have been used.

Action

One of the tasks performed by Chkdsk /F on an HPFS formatted device is to move data out of the special hotfix sectors and into a free good sector elsewhere on the device. You should run Chkdsk /F against the device to empty the hotfix sectors and make them available again to HPFS. However, you may also want to have the disk drive and its related components checked. Running out of hotfix sectors indicates that the device is experiencing a larger than average number of failures during reads or writes.

As a final note, these errors are not specific to the LAN Manager version of HPFS (HPFS386). The information here should also apply to volumes formatted with the standard OS/2 HPFS. Also, it is a good rule of thumb to run Chkdsk /F before reaccessing any drive that has experienced an error. If the data on the device is critical, you may also want to have the device and its related hardware checked. Finally, the best advice is to always keep critical data backed up on secondary devices, since you can never tell when a problem may occur.