Quatech Announcement: Difference between revisions

From OS2World.Com Wiki
Jump to navigation Jump to search
Jugbogdan (talk | contribs)
Jugbogdan (talk | contribs)
 
Line 93: Line 93:
  DS-300 (RS-485) $210.00
  DS-300 (RS-485) $210.00


=DSDP-100 Serial Communication 2 RS-232 and 2 Parallel Channels (SP-1000/SP-1050 for MCA provide similar function)=
==DSDP-100 Serial Communication 2 RS-232 and 2 Parallel Channels (SP-1000/SP-1050 for MCA provide similar function)==
 
;FEATURES:
==FEATURES:==
*2 Independent bi-directional parallel printer ports
*2 Independent bi-directional parallel printer ports
*Two independent RS-232 serial ports
*Two independent RS-232 serial ports
Line 102: Line 101:
*Optional 16550 UARTs available
*Optional 16550 UARTs available


==DESCRIPTION:==
;DESCRIPTION:
 
The DSDP-100 is a multiple channel communication board which supports two parallel ports and two RS-232 serial ports. Each serial port uses a 16450 UART supporting baud rates to 56K.
The DSDP-100 is a multiple channel communication board which supports two parallel ports and two RS-232 serial ports. Each serial port uses a 16450 UART supporting baud rates to 56K.
Optionally available are 16550 UARTs which support baud rates to 256K and provide an additional FIFO mode to reduce CPU overhead. Each Centronics compatible parallel interface consists of an eight bit bi-directional data port, a five bit status port, and a five bit command port.
Optionally available are 16550 UARTs which support baud rates to 256K and provide an additional FIFO mode to reduce CPU overhead. Each Centronics compatible parallel interface consists of an eight bit bi-directional data port, a five bit status port, and a five bit command port.
Line 111: Line 109:
The DSDP-100 occupies only one expansion slot in the PC. All ports may be accessed through a high density D-62 connector. An adapter cable is included to convert the D-62 into 2 D-25 female (parallel port) and 2 D-25 male (serial port) connectors.
The DSDP-100 occupies only one expansion slot in the PC. All ports may be accessed through a high density D-62 connector. An adapter cable is included to convert the D-62 into 2 D-25 female (parallel port) and 2 D-25 male (serial port) connectors.


==ADDRESS/INTERRUPT SELECTIONS:==
;ADDRESS/INTERRUPT SELECTIONS:
 
All four ports of the DSDP-100 are address selectable using a block of 8 dip switches. This allows each serial port to reside in any 8-byte I/O address range from 0000H to 03F8H. Similarly the parallel ports may reside in any 4-byte I/O address range from 0000H to 03FCH.
All four ports of the DSDP-100 are address selectable using a block of 8 dip switches. This allows each serial port to reside in any 8-byte I/O address range from 0000H to 03F8H. Similarly the parallel ports may reside in any 4-byte I/O address range from 0000H to 03FCH.


Line 119: Line 116:
Each port of the DSDP-100 can be enabled or disabled by setting the appropriate jumper as defined in the manual.
Each port of the DSDP-100 can be enabled or disabled by setting the appropriate jumper as defined in the manual.


==POWER CONSUMPTION:==
;POWER CONSUMPTION:
 
DSDP-100
DSDP-100
:+5V: 586mA (typ), 659mA (max)  
:+5V: 586mA (typ), 659mA (max)  
Line 131: Line 127:


DSDP-100 $195.00
DSDP-100 $195.00
<PRE>
<PRE>
QUATECH, INCORPORATED
QUATECH, INCORPORATED

Latest revision as of 23:13, 11 March 2025

QUATECH, INCORPORATED
662 Wolf Ledges Parkway
Akron, Ohio 44311
USA

1-800-553-1170
(216) 434-3154

CIS ID: 71155, 3427

Communications, Data Acquisition, and Control products for IBM PCs, PS/2s and compatibles using ISA and Micro Channel Buses

Quatech is an American company that proudly designs and manufactures its products in Akron, Ohio for worldwide distribution. Call for international distributor information.

Our products include intelligent and non-intelligent synchronous and asynchronous communications adapters offering up to eight ports, parallel port adapters, and a wide variety of data acquisition and waveform synthesis adapters.

Call Quatech at 1-800-553-1170 for a free catalog listing all products.

Listed below are some of our popular two-port asynchronous communications adapters suitable for use as OS/2 2.0 COM ports. One card also includes parallel ports with full IRQ support.

A MICRO CHANNEL VERSION OF EACH CARD IS AVAILABLE WITH 16550 UARTS STANDARD.

QUATECH, INC. 1-800-553-1170 (216) 434-3154

CIS ID: 71155, 3427

DS-100 Asynchronous Serial Adapter RS-232 for AT (DS-1000 for MCA)

FEATURES
  • Two independent RS-232 serial interfaces
  • AT bus (16 bit) compatible
  • Selectable and shareable interrupt features
  • Programmable baud rates to 56 Kbaud (Optional 16550s available)
  • DTE/DCE selection
DESCRIPTION

The DS-100 is a two channel asynchronous serial RS-232 communication adapter with versatile interrupt selection for the IBM AT. The adapter features the extended 16-bit AT bus, which provides access to the computer's additional interrupts. The DS-100 has a versatile interrupt feature which allows the user to select the desired interrupt, or to share an interrupt with another device. Users may select from interrupts IRQ2-7, 10-12 or 14-15.

The extended base address capability of the DS-100 supports any COM port. Two 16450 UART's provide two independent ports, allowing the user to communicate to two separate devices. The DS-100 supports baud rates to 56K (maximum of 256K with optional 16550). In case a limited number of interrupt levels are available for system expansion, the DS-100 is capable of sharing an interrupt with another device with the same feature.

ADDRESSING

Both serial communication ports have user-selectable addresses via two DIP switches. These switches allow each serial port to reside anywhere in the I/O space on eight byte boundaries. Bits A0, A1, and A2 are used to access the eight internal registers of the 16450. Each channel also offers enable/disable capabilities.

Decoding of all 16 address lines provides compatibility with systems using COM3 at 3220H and COM4 at 3228 while also greatly reducing the possibility of addressing conflicts in I/O intensive systems.

CONNECTOR: D-9 MALE

PIN 1 	Carrier Detect          PIN 6 	Data Set Ready
PIN 2 	Data Input              PIN 7	Request To Send
PIN 3 	Data Output             PIN 8	Clear To Send
PIN 4 	Data Terminal Ready     PIN 9	Ring Indicator
PIN 5 	Signal Ground
SPECIFICATIONS

POWER CONSUMPTION

+5V: 390mA (typ) 443mA (max).
+12V: 38mA (typ) 46mA (max).
-12V: 36mA (typ) 43mA(max).
DS-100.......................................$155.00
D-9 to D-25 Cable..............................$7.95

DS-200/DS-300 Asynchronous Serial Adapter RS-422/RS-485 for AT (DS-2000/DS-3000 for MCA)

FEATURES
  • Two independent interfaces
  • AT bus (16 bit) compatible
  • RTS-CTS Control Lines Available
  • Balanced RS-422 or RS-485 differential driver and receivers.
  • Maximum data transfer to 56Kbaud (Optional 16550s available)
DESCRIPTION

The DS-200 is a two port asynchronous serial RS-422 (DS-300 for RS-485) communication adapter with versatile interrupt selection for the IBM AT. The adapter features the extended 16-bit AT bus, which provides access to the computer's additional interrupts.

The DS-200 has a versatile interrupt feature which allows the user to select the desired interrupt, or to share an interrupt with another device. Users may select from interrupts IRQ2-7, 10-12 or 14-15.

The extended base address capability of the DS-200 supports any COM port. Two 16450 UART's provide two independent ports, allowing the user to communicate two separate devices. The DS-200 supports a maximum baud rate of 56K bits per second, 256K with 16550. In case a limited number of interrupt levels are available for system expansion, the DS-200 is capable of sharing an interrupt with another device with the same feature.

ADDRESSING

Both serial communication ports have user-selectable addresses via two DIP switches. These switches allow each serial port to reside anywhere in the I/O space on eight byte boundaries. Bits A0, A1, and A2 are used to access the eight internal registers of the 16450. Each channel also offers enable/disable capabilities.

Decoding of all 16 address lines provides compatibility with systems using COM3 at 3220H and COM4 at 3228H while also greatly reducing the possibility of addressing conflicts in I/O intensive systems.

CONNECTOR: D-9 FEMALE

PIN 1	Auxiliary Output +    PIN 6	Auxiliary Output
PIN 2	Data Output +         PIN 7	Data Output
PIN 3	Signal Ground         PIN 8	Data Input
PIN 4	Data Input +          PIN 9	Auxiliary Input
PIN 5	Auxiliary Input +
SPECIFICATIONS

POWER CONSUMPTION: +5v: 464mA (typ), 530mA (max)

DS-200 (RS-422)	$210.00
DS-300 (RS-485)	$210.00

DSDP-100 Serial Communication 2 RS-232 and 2 Parallel Channels (SP-1000/SP-1050 for MCA provide similar function)

FEATURES
  • 2 Independent bi-directional parallel printer ports
  • Two independent RS-232 serial ports
  • All ports are address selectable
  • All ports have selectable/shareable interrupts (IRQ2-IRQ7)
  • Optional 16550 UARTs available
DESCRIPTION

The DSDP-100 is a multiple channel communication board which supports two parallel ports and two RS-232 serial ports. Each serial port uses a 16450 UART supporting baud rates to 56K. Optionally available are 16550 UARTs which support baud rates to 256K and provide an additional FIFO mode to reduce CPU overhead. Each Centronics compatible parallel interface consists of an eight bit bi-directional data port, a five bit status port, and a five bit command port.

Each printer port of the DSDP-100 supports bi-directional data transfer. This feature allows data to be input through the printer interface. Both the serial and parallel interfaces are address selectable allowing the ports to be installed in the computer without conflicting with other devices. Each port may also be individually enabled or disabled. Versatile interrupt circuitry allows each port access to IRQ2-IRQ7. The DSDP-100 also has interrupt sharing capabilities, allowing it to share interrupts with other Quatech adapters supporting this feature.

The DSDP-100 occupies only one expansion slot in the PC. All ports may be accessed through a high density D-62 connector. An adapter cable is included to convert the D-62 into 2 D-25 female (parallel port) and 2 D-25 male (serial port) connectors.

ADDRESS/INTERRUPT SELECTIONS

All four ports of the DSDP-100 are address selectable using a block of 8 dip switches. This allows each serial port to reside in any 8-byte I/O address range from 0000H to 03F8H. Similarly the parallel ports may reside in any 4-byte I/O address range from 0000H to 03FCH.

Each port of the DSDP-100 may select an interrupt in the range IRQ2-IRQ7 using a six position jumper block. An interrupt sharing circuit implemented on the board allows multiple ports to share the same interrupt level or to share the interrupt with another Quatech adapter supporting this feature.

Each port of the DSDP-100 can be enabled or disabled by setting the appropriate jumper as defined in the manual.

POWER CONSUMPTION

DSDP-100

+5V: 586mA (typ), 659mA (max)
+12V: 38mA (typ), 46mH (max)
-12V: 36mA (typ), 43mH (max)

BAUD RATE:

57,600 bits/sec max (16450)
256,000 bits/sec max (optional 16550)

DSDP-100 $195.00

QUATECH, INCORPORATED
662 Wolf Ledges Parkway
Akron, Ohio 44311
USA

1-800-553-1170
(216) 434-3154

CIS ID: 71155, 3427