Author Topic: TRAP d Intel DH55PJ  (Read 1853 times)

jdeb

  • Newbie
  • *
  • Posts: 40
    • View Profile
TRAP d Intel DH55PJ
« on: 2012.03.17, 17:11:49 »
I am looking into finding the latest hardware for eCS2.1. My current build is fine but I am considering building eCS PC's. I got a trap d.
System Specs... Intel DH55PJ / Intel Pentium G6951 / 4GB DDR3-1333 / Intel 320 SSD

Trap d right out of gate. I tried a few settings in the BIOS like single core mode, ACHI, Legacy, Compatible. Boots Linux fine.
I think the issue is the CPU as it is one that Intel released as a software CPU upgrade. The upgrade would unlock additional cache. I do not have any i3. 5 or 7's (LGA1156) lying around to swap.
I created a ticket. Any suggestions?

Code: [Select]
TRAP 000d      ERRCD=f000 ERACC=**** ERLIM=******** cpu=01
EAX=00000301 EBX=00000101 ECX=00000101 EDX=00000101
ESI=00000000 EDI=fb80017f EBP=0000bd8b FLG=00010293
CS:EIP=0440:000003fe CSACC=109b CSLIM=0000ffff
SS:ESP=0448:000003d4 SSACC=1093 SSLIM=000003ff
DS=0108 DSAACC=0093 DSLIM=000085bf CR0=80010013
ES=04b0 ESACC=00f3 ESLIM=0000032b CR2=ffdeb000
FS=0000 FSACC=**** FSLIM=********
GS=0000 GSACC=**** GSLIM=********

The system detected an internal processing error at
location ##0168:fff0f667 - 000f:e667.
60000, 9084

10860655
Internal revision 14.105_SMP

The system is stopped. Record all of the above information and
contact your service representative.

Foxconn P41A-P, Intel E7500, 2 GB DDR2 800, ATI X300, ADATA Sata II 64 GB SSD, 160GB WD Sata II HD, Intel Pro 100/1000, Antec Basiq 350W PS, Antec 300 Case, ECS 2.1

rwklein

  • Full Member
  • ***
  • Posts: 166
    • View Profile
Re: TRAP d Intel DH55PJ
« Reply #1 on: 2012.03.17, 23:19:05 »
I am looking into finding the latest hardware for eCS2.1. My current build is fine but I am considering building eCS PC's. I got a trap d.
System Specs... Intel DH55PJ / Intel Pentium G6951 / 4GB DDR3-1333 / Intel 320 SSD

Trap d right out of gate. I tried a few settings in the BIOS like single core mode, ACHI, Legacy, Compatible. Boots Linux fine.
I think the issue is the CPU as it is one that Intel released as a software CPU upgrade. The upgrade would unlock additional cache. I do not have any i3. 5 or 7's (LGA1156) lying around to swap.
I created a ticket. Any suggestions?

Code: [Select]
TRAP 000d      ERRCD=f000 ERACC=**** ERLIM=******** cpu=01
EAX=00000301 EBX=00000101 ECX=00000101 EDX=00000101
ESI=00000000 EDI=fb80017f EBP=0000bd8b FLG=00010293
CS:EIP=0440:000003fe CSACC=109b CSLIM=0000ffff
SS:ESP=0448:000003d4 SSACC=1093 SSLIM=000003ff
DS=0108 DSAACC=0093 DSLIM=000085bf CR0=80010013
ES=04b0 ESACC=00f3 ESLIM=0000032b CR2=ffdeb000
FS=0000 FSACC=**** FSLIM=********
GS=0000 GSACC=**** GSLIM=********

The system detected an internal processing error at
location ##0168:fff0f667 - 000f:e667.
60000, 9084

10860655
Internal revision 14.105_SMP

The system is stopped. Record all of the above information and
contact your service representative.



Hello

Roderick Klein here from Mensys. I have typed this a million times to a lot of people. But the knowledge on these types of system crashes can normally not be found on these forums. Oke I stand corrected, sorry :-) I just see an email coming in from the ticket system of eComStation.

Oke the TRAP you have is a known one. Its a defect in the OEMHLP service in the kernel.

From our eCOmStation bugtracker bug 3093:
This could be seen as a defect in OS2DLR that contains a portion of the OEMHLP code of OS/2. Its blowing because of defect/not properly tested code in the BIOS.
The new ACPI version we will release this year should fix this!

As documented in bug 2981 I wrote:

This WILL fix this issue plus a list of items that is to long to mention :-)
ACPI has made a lot of progress with David working on it.

The new PSD is hopefully released before the 25th of November. We are working on a new public beta that will install a fixed keyboar driver as well. The driver had a defect as well!

This new version will not solve the problem for people this trap.
It will not fix in the *sense* you would need to have computer with a floppy drive to load the new ACPI.PSD to boot from CD. When ACPI version 3.19.11 is released you need to install eCS on a different system and put the ACPI version on the hard disc. Then move the hard disc to the failling system.

A refresh of eCS is of course planned with a new ACPI version included.

Our PSD patches OEMHLP$ service offered by the kernel out in memory. Its the old OEMHLP service in the kernel that fails! Fixing screen01.sys is not a solution. Since any device driver that would call into OEMHLP could cause the same trap.

This seems to be a ""defect"" in more modern BIOS'es.
(end of bug)

These ACPI versions have been released as ACPI 3.19.14/3.19.15.
Version 3.19.16 is in the pipeline.


Roderick Klein
Mensys

Blonde Guy

  • Sr. Member
  • ****
  • Posts: 283
    • View Profile
    • Blonde Guy
Re: TRAP d Intel DH55PJ
« Reply #2 on: 2012.04.04, 05:57:24 »
I got an ASRock H55M-LE, which would be pretty similar to the Intel part

This one can boot from eCS 2.1, but has several problems.

1. eCS does not detect any USB 1.1, so USBUHCD.SYS is not installed. Two instances of USBEHCD.SYS are loaded and USB 2.0 works, but USB keyboard and mouse are flaky without USB 1.1 support.

2. No sound from UniAud. UniMix gives only three parameters to play with -- none of them enable sound.

3. Panorama works OK, but if widescreen is enabled, it no longer syncs with the monitor, and looks bad.

Quote
PCI Dump 3 Apr 2012 17:59:58
lspci version 2.2.3
00:00.0 0600: 8086:0040 (rev 18)
00:02.0 0300: 8086:0042 (rev 18)
00:1a.0 0c03: 8086:3b3c (rev 06)
00:1b.0 0403: 8086:3b56 (rev 06)
00:1c.0 0604: 8086:3b42 (rev 06)
00:1c.4 0604: 8086:3b4a (rev 06)
00:1c.5 0604: 8086:3b4c (rev 06)
00:1d.0 0c03: 8086:3b34 (rev 06)
00:1e.0 0604: 8086:244e (rev a6)
00:1f.0 0601: 8086:3b06 (rev 06)
00:1f.2 0101: 8086:3b20 (rev 06)
00:1f.3 0c05: 8086:3b30 (rev 06)
00:1f.5 0101: 8086:3b26 (rev 06)
01:00.0 0200: 10ec:8168 (rev 03)
PCI Detailed Dump
00:00.0 Host bridge: Intel Corporation Unknown device 0040 (rev 18)
   Subsystem: ASRock Incorporation Unknown device 0040
   Flags: bus master, fast devsel, latency 0
   Capabilities: [e0] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation Unknown device 0042 (rev 18) (prog-if 00 [VGA])
   Subsystem: ASRock Incorporation Unknown device 0042
   Flags: bus master, fast devsel, latency 0, IRQ 16
   Memory at fb800000 (64-bit, non-prefetchable)
   Memory at d0000000 (64-bit, prefetchable)
   I/O ports at cc00
   Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
   Capabilities: [d0] Power Management version 2
   Capabilities: [a4] #13 [0306]

00:1a.0 USB Controller: Intel Corporation Unknown device 3b3c (rev 06) (prog-if 20 [EHCI])
   Subsystem: ASRock Incorporation Unknown device 3b3c
   Flags: bus master, medium devsel, latency 0, IRQ 16
   Memory at fbff6000 (32-bit, non-prefetchable)
   Capabilities: [50] Power Management version 2
   Capabilities: [58] Debug port
   Capabilities: [98] #13 [0306]

00:1b.0 Audio device: Intel Corporation Unknown device 3b56 (rev 06)
   Subsystem: ASRock Incorporation Unknown device 2718
   Flags: bus master, fast devsel, latency 0, IRQ 22
   Memory at fbff8000 (64-bit, non-prefetchable)
   Capabilities: [50] Power Management version 2
   Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
   Capabilities: [70] Express Unknown type IRQ 0

00:1c.0 PCI bridge: Intel Corporation Unknown device 3b42 (rev 06) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
   Prefetchable memory behind bridge: 00000000faf00000-00000000faf00000
   Capabilities: [40] Express Root Port (Slot-) IRQ 0
   Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
   Capabilities: [90] #0d [0000]
   Capabilities: [a0] Power Management version 2

00:1c.4 PCI bridge: Intel Corporation Unknown device 3b4a (rev 06) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
   Prefetchable memory behind bridge: 00000000fae00000-00000000fae00000
   Capabilities: [40] Express Root Port (Slot+) IRQ 0
   Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
   Capabilities: [90] #0d [0000]
   Capabilities: [a0] Power Management version 2

00:1c.5 PCI bridge: Intel Corporation Unknown device 3b4c (rev 06) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
   I/O behind bridge: 0000e000-0000efff
   Prefetchable memory behind bridge: 00000000fad00000-00000000fad00000
   Capabilities: [40] Express Root Port (Slot-) IRQ 0
   Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
   Capabilities: [90] #0d [0000]
   Capabilities: [a0] Power Management version 2

00:1d.0 USB Controller: Intel Corporation Unknown device 3b34 (rev 06) (prog-if 20 [EHCI])
   Subsystem: ASRock Incorporation Unknown device 3b34
   Flags: bus master, medium devsel, latency 0, IRQ 23
   Memory at fbffc000 (32-bit, non-prefetchable)
   Capabilities: [50] Power Management version 2
   Capabilities: [58] Debug port
   Capabilities: [98] #13 [0306]

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) (prog-if 01 [Subtractive decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
   Capabilities: [50] #0d [0000]

00:1f.0 ISA bridge: Intel Corporation Unknown device 3b06 (rev 06)
   Subsystem: ASRock Incorporation Unknown device 3b06
   Flags: bus master, medium devsel, latency 0
   Capabilities: [e0] Vendor Specific Information

00:1f.2 IDE interface: Intel Corporation Unknown device 3b20 (rev 06) (prog-if 8a [Master SecP PriP])
   Subsystem: ASRock Incorporation Unknown device 3b20
   Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
   I/O ports at <unassigned>
   I/O ports at <unassigned>
   I/O ports at <unassigned>
   I/O ports at <unassigned>
   I/O ports at ff90
   I/O ports at ffa0
   Capabilities: [70] Power Management version 3
   Capabilities: [b0] #13 [0306]

00:1f.3 SMBus: Intel Corporation Unknown device 3b30 (rev 06)
   Subsystem: ASRock Incorporation Unknown device 3b30
   Flags: medium devsel, IRQ 18
   Memory at fbfffc00 (64-bit, non-prefetchable)
   I/O ports at 0400

00:1f.5 IDE interface: Intel Corporation Unknown device 3b26 (rev 06) (prog-if 85 [Master SecO PriO])
   Subsystem: ASRock Incorporation Unknown device 3b26
   Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
   I/O ports at dc00
   I/O ports at d880
   I/O ports at d800
   I/O ports at d480
   I/O ports at d400
   I/O ports at d080
   Capabilities: [70] Power Management version 3
   Capabilities: [b0] #13 [0306]

01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Unknown device 8168 (rev 03)
   Subsystem: ASRock Incorporation Unknown device 8168
   Flags: bus master, fast devsel, latency 0, IRQ 17
   I/O ports at e800
   Memory at fadff000 (64-bit, prefetchable)
   Memory at fadf8000 (64-bit, prefetchable)
   Capabilities: [40] Power Management version 3
   Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
   Capabilities: [70] Express Endpoint IRQ 1
   Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4
   Capabilities: [cc] Vital Product Data

Expert Consulting for OS/2 and eComStation

DougB

  • Sr. Member
  • ****
  • Posts: 407
    • View Profile
Re: TRAP d Intel DH55PJ
« Reply #3 on: 2012.04.04, 07:40:20 »
Quote
1. eCS does not detect any USB 1.1, so USBUHCD.SYS is not installed. Two instances of USBEHCD.SYS are loaded and USB 2.0 works, but USB keyboard and mouse are flaky without USB 1.1 support.

Are you sure that it has USB other than EHCI adapters? I have a lenovo ThinkPad T510, and it has two EHCI adapters, and no others. USB 1.0, and 1.1, work fine when using only the USBEHCD.SYS  driver (two of them). Somehow, the hardware supports the older USB versions. FWIW, I am using the latest drivers as posted at HOBBES:

http://hobbes.nmsu.edu/download/pub/os2/system/drivers/misc/usbhcd183.zip

rudi

  • Full Member
  • ***
  • Posts: 116
    • View Profile
Re: TRAP d Intel DH55PJ
« Reply #4 on: 2012.04.04, 08:38:30 »
it has two EHCI adapters, and no others. USB 1.0, and 1.1, work fine when using only the USBEHCD.SYS  driver (two of them).

The USB specs allow a "2.0-only" configuration in case there is an integrated hub that can handle 1.x devices. Some Intel hardware is known to do exactly this. However, the crappy OS/2 USB drivers did not work correctly in this scenario. Lars has implemented some fixes. So using his driver (from Hobbes) will increase the chances for getting this to work...

RobertM

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2034
    • View Profile
    • A.I.BuiltPC - using OS/2 Warp Server & eComStation for Custom Web and Database Solutions
Re: TRAP d Intel DH55PJ
« Reply #5 on: 2012.04.04, 09:57:12 »
it has two EHCI adapters, and no others. USB 1.0, and 1.1, work fine when using only the USBEHCD.SYS  driver (two of them).

The USB specs allow a "2.0-only" configuration in case there is an integrated hub that can handle 1.x devices. Some Intel hardware is known to do exactly this. However, the crappy OS/2 USB drivers did not work correctly in this scenario. Lars has implemented some fixes. So using his driver (from Hobbes) will increase the chances for getting this to work...


Here's the driver (link goes to details page):
http://hobbes.nmsu.edu/h-viewer.php?dir=/pub/os2/system/drivers/misc&file=usbhcd183.zip

And an interesting driver for the v1.1 stuff (link to Hobbes details page):
http://hobbes.nmsu.edu/h-viewer.php?dir=/pub/os2/system/drivers/misc&file=usbecd12s.zip

Best,
Rob
|
|
Kirk's 5 Year Mission Continues at:
Star Trek New Voyages
|
|


xchris

  • Newbie
  • *
  • Posts: 49
    • View Profile
Re: TRAP d Intel DH55PJ
« Reply #6 on: 2012.04.04, 13:25:21 »
Quote
This new version will not solve the problem for people this trap.
It will not fix in the *sense* you would need to have computer with a floppy drive to load the new ACPI.PSD to boot from CD. When ACPI version 3.19.11 is released you need to install eCS on a different system and put the ACPI version on the hard disc. Then move the hard disc to the failling system.

Is there any way to put that driver into the existing boot install CD?
I used the winISO in order to insert the reg_key as a file, so to avoid type it...

chris

Blonde Guy

  • Sr. Member
  • ****
  • Posts: 283
    • View Profile
    • Blonde Guy
Re: TRAP d Intel DH55PJ
« Reply #7 on: 2012.04.04, 15:34:13 »
Quote
1. eCS does not detect any USB 1.1, so USBUHCD.SYS is not installed. Two instances of USBEHCD.SYS are loaded and USB 2.0 works, but USB keyboard and mouse are flaky without USB 1.1 support.

Are you sure that it has USB other than EHCI adapters? I have a lenovo ThinkPad T510, and it has two EHCI adapters, and no others. USB 1.0, and 1.1, work fine when using only the USBEHCD.SYS  driver (two of them). Somehow, the hardware supports the older USB versions. FWIW, I am using the latest drivers as posted at HOBBES:

http://hobbes.nmsu.edu/download/pub/os2/system/drivers/misc/usbhcd183.zip

I'm also using 10.183 drivers, although 10.162 behave the same. The mouse and keyboard work (in legacy mode) through a KVM. They work fine until I switch away. The computer never detects that I've switched back. You might not notice that if you don't use a KVM.
Expert Consulting for OS/2 and eComStation

DougB

  • Sr. Member
  • ****
  • Posts: 407
    • View Profile
Re: TRAP d Intel DH55PJ
« Reply #8 on: 2012.04.04, 17:14:35 »
I don't know how they make the USB 1.1 and 1.0 devices work (it is likely a built in hub as noted earlier). I also don't use a KVM device, which may actually be causing your problems. Have you tried it without that?

I can use my 1 TB external USB 2.0 disk, I can use my 640 GB external USB 2.0 disk, I can use my wireless mouse (USB 1.1), I can use my Lexar Jumpdrive Trio with various media sizes (USB 2.0), I can use my ancient IBM 8 MB memory stick (USB 1.0), and I can use my USB printer (USB 1.1), without any problems, at all. I have also tried an old USB 1.1 hub with it. The USB 2.0 drivers, whether 10.183, or 10.162, have no trouble with this setup. There were a couple of earlier updated drivers that didn't do USB 1.0, but that got fixed when I pointed it out.

Frankly, I was unpleasantly surprised when I discovered that the T510 only has 2 EHCI adapters, and no others, but that turned to a pleasant surprise when I tried the USB 1.x devices, and they all worked perfectly. After doing some investigating, I found out that the T510 was supposed to have only USB 3.0 adapters, but somehow that got scrapped, and it got shipped with USB 2.0 adapters. I don't know if it has USB 3.0 hardware, that has been reprogrammed to be USB 2.0, or if the hardware got changed. All I know is, that it works great, for me. According to Win7, they are Intel 5 series/3400 Series chipset Family USB Enhanced controller devices. I am waiting for the day when a BIOS update turns them into USB3.0 controllers  ???  Then, I may have a problem.

In any case, it seems that you do not need, or get, USB 1.x controllers any more, in some machines.