HP EliteBook Folio 9470m Hardware Report
Jump to navigation
Jump to search
Back to HP EliteBook Folio 9470m
PCI Report
Craig Hart's PCI+AGP bus sniffer, Version 1.04vkA, freeware made in 1996-2005. Loaded Vendor Data : "This is version 2021.07.20 of pci.ids using ids2devs version 1.03" PCI BIOS Version 2.10 found! Number of PCI Busses : 4 PCI Characteristics : Config Mechanism 1 Searching for PCI Devices using the OEMHLP$ driver Bus 0 (PCI Express), Device Number 0, Device Function 0 Vendor 8086h Intel Corporation Device 0154h 3rd Gen Core processor DRAM Controller Command 0006h (Memory Access, BusMaster) Status 2090h (Has Capabilities List, Supports Back-To-Back Trans., Received Master Abort, Fast Timing) Revision 09h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Bridge, type PCI to HOST Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company New Capabilities List Present: Vendor-Dependant Capability Bus 0 (PCI Express), Device Number 2, Device Function 0 Vendor 8086h Intel Corporation Device 0166h 3rd Gen Core processor Graphics Controller Command 0007h (I/O Access, Memory Access, BusMaster) Status 0090h (Has Capabilities List, Supports Back-To-Back Trans., Fast Timing) Revision 09h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Display, type VGA Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (64-bit) : D0000000h Address 2 is a Memory Address (64-bit, Prefetchable) : C0000000h Address 4 is an I/O Port : 2000h System IRQ 16, INT# A New Capabilities List Present: Message Signalled Interrupt Capability MSI is disabled MSI function can generate 32-bit addresses Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Does not support PME# signalling Current Power State : D0 (Device operational, no power saving) Unknown Capability (Code 13h)!! Bus 0 (PCI Express), Device Number 20, Device Function 0 Vendor 8086h Intel Corporation Device 1E31h 7 Series/C210 Series Chipset Family USB xHCI Host Controller Command 0006h (Memory Access, BusMaster) Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type USB (UHCI), programming interface 30 Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (64-bit) : D0720000h..D072FFFFh System IRQ 10, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 375 mA Current Power State : D0 (Device operational, no power saving) Message Signalled Interrupt Capability MSI is disabled MSI function can generate 64-bit addresses Bus 0 (PCI Express), Device Number 22, Device Function 0 Vendor 8086h Intel Corporation Device 1E3Ah 7 Series/C216 Chipset Family MEI Controller #1 Command 0006h (Memory Access, BusMaster) Status 0010h (Has Capabilities List, Fast Timing) Revision 04h, Header Type 80h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Simple Communication, type Other Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (64-bit) : D0735000h System IRQ 16, INT# A New Capabilities List Present: Power Management Capability, Version 1.2 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Message Signalled Interrupt Capability MSI is disabled MSI function can generate 64-bit addresses Bus 0 (PCI Express), Device Number 25, Device Function 0 Vendor 8086h Intel Corporation Device 1502h 82579LM Gigabit Network Connection (Lewisville) Command 0007h (I/O Access, Memory Access, BusMaster) Status 0010h (Has Capabilities List, Fast Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Network, type Ethernet Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (0-4GiB) : D0700000h..D071FFFFh Address 1 is a Memory Address (0-4GiB) : D073A000h..D073AFFFh Address 2 is an I/O Port : 2060h..207Fh System IRQ 17, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) 700 mW D0 power consume 700 mW D0 power dissipate 200 mW D3 power consume 200 mW D3 power dissipate 0 mW common logic power consume Message Signalled Interrupt Capability MSI is enabled MSI function can generate 64-bit addresses Unknown Capability (Code 13h)!! Bus 0 (PCI Express), Device Number 26, Device Function 0 Vendor 8086h Intel Corporation Device 1E2Dh 7 Series/C216 Chipset Family USB Enhanced Host Controller #2 Command 0006h (Memory Access, BusMaster) Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type USB 2.0 (EHCI) Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (0-4GiB) : D0739000h..D07393FFh System IRQ 16, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 375 mA Current Power State : D0 (Device operational, no power saving) USB 2.0 EHCI Debug Port Capability Unknown Capability (Code 13h)!! Bus 0 (PCI Express), Device Number 27, Device Function 0 Vendor 8086h Intel Corporation Device 1E20h 7 Series/C216 Chipset Family High Definition Audio Controller Command 0006h (Memory Access, BusMaster) Status 0010h (Has Capabilities List, Fast Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) Cache line size 64 Bytes (16 DWords) PCI Class Multimedia, type Unknown! Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (64-bit) : D0730000h..D0733FFFh System IRQ 22, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 55 mA Current Power State : D0 (Device operational, no power saving) Message Signalled Interrupt Capability MSI is enabled MSI function can generate 64-bit addresses PCI Express Capability, Version 1 Device/Port Type : Root Complex Integrated Endpoint Device Unsupported Request Severity is Non-Fatal Device Status : AUX Power Detected Link Capabilities : Maximum Link speed : Unknown (00h)!! Maximum Link Width : xReserved Link Port Number : 0 Link Control : Asynchronous Clocking in Use Link Status : Current Link speed : Unknown (00)!! Current Link Width : x0 Bus 0 (PCI Express), Device Number 28, Device Function 0 Vendor 8086h Intel Corporation Device 1E10h 7 Series/C216 Chipset Family PCI Express Root Port 1 Command 0407h (I/O Access, Memory Access, BusMaster, Interrupt Disable) Status 0010h (Has Capabilities List, Fast Timing) Revision C4h, Header Type 81h, Bus Latency Timer 00h Self test 00h (Self test not supported) Cache line size 64 Bytes (16 DWords) PCI Class Bridge, type PCI to PCI Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company System IRQ 17, INT# A PCI Bridge Information: Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus number 1 Secondary Bus Command 0000h Secondary Bus Status 2000h (Received Master Abort, Fast Timing) Secondary Bus Latency 00h I/O Port Range Passed to Secondary Bus : None Memory Range Passed to Secondary Bus : D0600000h..D06FFFFFh Prefetchable Memory Range Passed to Secondary Bus : None New Capabilities List Present: PCI Express Capability, Version 2 Device/Port Type : Root port of PCI Express Root Complex Port Type : Port is an Expansion Slot Unsupported Request Severity is Non-Fatal Device Status : AUX Power Detected Link Capabilities : Maximum Link speed : Unknown (02h)!! Maximum Link Width : x1 Link Port Number : 1 Link Control : Asynchronous Clocking in Use Link Status : Current Link speed : 2.5Gb/s Current Link Width : x0 Slot Capabilities : Slot Power Limit Value : 2.000 Watts Physical slot Number 0 Message Signalled Interrupt Capability MSI is disabled MSI function can generate 32-bit addresses Subsystem ID & Subsystem Vendor ID Capability SSVID : 103Ch SSID : 18DFh Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Bus 0 (PCI Express), Device Number 28, Device Function 2 Vendor 8086h Intel Corporation Device 1E14h 7 Series/C210 Series Chipset Family PCI Express Root Port 3 Command 0407h (I/O Access, Memory Access, BusMaster, Interrupt Disable) Status 0010h (Has Capabilities List, Fast Timing) Revision C4h, Header Type 81h, Bus Latency Timer 00h Self test 00h (Self test not supported) Cache line size 64 Bytes (16 DWords) PCI Class Bridge, type PCI to PCI Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company System IRQ 18, INT# C PCI Bridge Information: Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus number 2 Secondary Bus Command 0000h Secondary Bus Status 2000h (Received Master Abort, Fast Timing) Secondary Bus Latency 00h I/O Port Range Passed to Secondary Bus : None Memory Range Passed to Secondary Bus : D0500000h..D05FFFFFh Prefetchable Memory Range Passed to Secondary Bus : None New Capabilities List Present: PCI Express Capability, Version 2 Device/Port Type : Root port of PCI Express Root Complex Port Type : Port is an Expansion Slot Unsupported Request Severity is Non-Fatal Device Status : AUX Power Detected Link Capabilities : Maximum Link speed : Unknown (02h)!! Maximum Link Width : x1 Link Port Number : 3 Link Control : Common Clock Configuration In Use Link Status : Current Link speed : 2.5Gb/s Current Link Width : x1 Slot Capabilities : Slot Power Limit Value : 6.000 Watts Physical slot Number 0 Message Signalled Interrupt Capability MSI is disabled MSI function can generate 32-bit addresses Subsystem ID & Subsystem Vendor ID Capability SSVID : 103Ch SSID : 18DFh Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Bus 0 (PCI Express), Device Number 28, Device Function 3 Vendor 8086h Intel Corporation Device 1E16h 7 Series/C216 Chipset Family PCI Express Root Port 4 Command 0007h (I/O Access, Memory Access, BusMaster) Status 0010h (Has Capabilities List, Fast Timing) Revision C4h, Header Type 81h, Bus Latency Timer 00h Self test 00h (Self test not supported) Cache line size 64 Bytes (16 DWords) PCI Class Bridge, type PCI to PCI Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company System IRQ 19, INT# D PCI Bridge Information: Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus number 3 Secondary Bus Command 0000h Secondary Bus Status 2000h (Received Master Abort, Fast Timing) Secondary Bus Latency 00h I/O Port Range Passed to Secondary Bus : None Memory Range Passed to Secondary Bus : D0400000h..D04FFFFFh Prefetchable Memory Range Passed to Secondary Bus : None New Capabilities List Present: PCI Express Capability, Version 2 Device/Port Type : Root port of PCI Express Root Complex Port Type : Port is an Expansion Slot Unsupported Request Severity is Non-Fatal Device Status : AUX Power Detected Link Capabilities : Maximum Link speed : Unknown (02h)!! Maximum Link Width : x1 Link Port Number : 4 Link Control : Common Clock Configuration In Use Link Status : Current Link speed : 2.5Gb/s Current Link Width : x1 Slot Capabilities : Slot Power Limit Value : 8.000 Watts Physical slot Number 0 Message Signalled Interrupt Capability MSI is disabled MSI function can generate 32-bit addresses Subsystem ID & Subsystem Vendor ID Capability SSVID : 103Ch SSID : 18DFh Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Bus 0 (PCI Express), Device Number 29, Device Function 0 Vendor 8086h Intel Corporation Device 1E26h 7 Series/C216 Chipset Family USB Enhanced Host Controller #1 Command 0006h (Memory Access, BusMaster) Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type USB 2.0 (EHCI) Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (0-4GiB) : D0738000h..D07383FFh System IRQ 16, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 375 mA Current Power State : D0 (Device operational, no power saving) USB 2.0 EHCI Debug Port Capability Unknown Capability (Code 13h)!! Bus 0 (PCI Express), Device Number 31, Device Function 0 Vendor 8086h Intel Corporation Device 1E55h QM77 Express Chipset LPC Controller Command 0007h (I/O Access, Memory Access, BusMaster) Status 0210h (Has Capabilities List, Medium Timing) Revision 04h, Header Type 80h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Bridge, type PCI to ISA Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company New Capabilities List Present: Vendor-Dependant Capability Bus 0 (PCI Express), Device Number 31, Device Function 2 Vendor 8086h Intel Corporation Device 1E01h 7 Series Chipset Family 4-port SATA Controller [IDE mode] Command 0007h (I/O Access, Memory Access, BusMaster) Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Trans., Medium Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Storage, type IDE (ATA) PCI EIDE Controller Features : BusMaster EIDE is supported Primary Channel is at I/O Port 01F0h and IRQ 14 Secondary Channel is at I/O Port 0170h and IRQ 15 Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is an I/O Port : 20D8h Address 1 is an I/O Port : 20ECh Address 2 is an I/O Port : 20D0h Address 3 is an I/O Port : 20E8h Address 4 is an I/O Port : 20B0h Address 5 is an I/O Port : 20A0h..20AFh System IRQ 19, INT# B New Capabilities List Present: Power Management Capability, Version 1.2 Does not support low power State D1 or D2 Does not support PME# signalling Current Power State : D0 (Device operational, no power saving) Unknown Capability (Code 13h)!! Bus 0 (PCI Express), Device Number 31, Device Function 3 Vendor 8086h Intel Corporation Device 1E22h 7 Series/C216 Chipset Family SMBus Controller Command 0003h (I/O Access, Memory Access) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type SMBus Controller Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is a Memory Address (64-bit) : D0734000h Address 2 is not present or not configured! Address 3 is not present or not configured! Address 4 is an I/O Port : EF80h System IRQ 18, INT# C Bus 0 (PCI Express), Device Number 31, Device Function 5 Vendor 8086h Intel Corporation Device 1E09h 7 Series Chipset Family 2-port SATA Controller [IDE mode] Command 0005h (I/O Access, BusMaster) Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Trans., Medium Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Storage, type IDE (ATA) PCI EIDE Controller Features : BusMaster EIDE is supported Primary Channel is in native mode at Addresses 0 & 1 Secondary Channel is in native mode at Addresses 2 & 3 Subsystem ID 18DF103Ch Unknown Subsystem Vendor 103Ch Hewlett-Packard Company Address 0 is an I/O Port : 20C8h Address 1 is an I/O Port : 20E4h Address 2 is an I/O Port : 20C0h Address 3 is an I/O Port : 20E0h Address 4 is an I/O Port : 2090h Address 5 is an I/O Port : 2080h System IRQ 19, INT# B New Capabilities List Present: Power Management Capability, Version 1.2 Does not support low power State D1 or D2 Does not support PME# signalling Current Power State : D0 (Device operational, no power saving) Unknown Capability (Code 13h)!! Bus 3 (PCI Express), Device Number 0, Device Function 0 Vendor 8086h Intel Corporation Device 088Eh Centrino Advanced-N 6235 Command 0006h (Memory Access, BusMaster) Status 0010h (Has Capabilities List, Fast Timing) Revision 24h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) Cache line size 64 Bytes (16 DWords) PCI Class Network, type Other Subsystem ID 40608086h Unknown Subsystem Vendor 8086h Intel Corporation Address 0 is a Memory Address (64-bit) : D0400000h System IRQ 19, INT# A New Capabilities List Present: Power Management Capability, Version 1.2 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Message Signalled Interrupt Capability MSI is disabled MSI function can generate 64-bit addresses PCI Express Capability, Version 1 Device/Port Type : PCI Express Endpoint Device Device Capabilities : Unsupported Request Severity is Fatal Device Status : Correctable Error Detected Unsupported Request Detected AUX Power Detected Link Capabilities : Maximum Link speed : 2.5Gb/s Maximum Link Width : x1 Link Port Number : 0 Link Control : Common Clock Configuration In Use Link Status : Current Link speed : 2.5Gb/s Current Link Width : x1 ROM PCI IRQ routing table Tests.... ROM IRQ routing table found at F000h:7E00h Table Version 1.0 - OK Table size 416 bytes - OK Table Checksum 44h - OK PCI Interrupt Router: QM77 Express Chipset LPC Controller IRQ's dedicated to PCI : None Error: table entries 10 and 12 refer to the same Bus=255/Device=0! Error: table entries 10 and 15 refer to the same Bus=255/Device=0! Error: table entries 10 and 16 refer to the same Bus=255/Device=0! Error: table entries 10 and 17 refer to the same Bus=255/Device=0! Error: table entries 12 and 15 refer to the same Bus=255/Device=0! Error: table entries 12 and 16 refer to the same Bus=255/Device=0! Error: table entries 12 and 17 refer to the same Bus=255/Device=0! Error: table entries 15 and 16 refer to the same Bus=255/Device=0! Error: table entries 15 and 17 refer to the same Bus=255/Device=0! Error: table entries 16 and 17 refer to the same Bus=255/Device=0! Error: connectivity mismatches for link value 61: Bus=0 Device=22 Pin=INTB# Map=7,10,11,15 Bus=255 Device= 0 Pin=INTB# Map=None Error: connectivity mismatches for link value 62: Bus=0 Device=22 Pin=INTC# Map=7,10,11,15 Bus=255 Device= 0 Pin=INTC# Map=None Error: connectivity mismatches for link value 63: Bus=0 Device=22 Pin=INTD# Map=7,10,11,15 Bus=255 Device= 0 Pin=INTD# Map=None The ROM PCI IRQ routing table appears to be faulty!! IRQ Summary: IRQs 10,14,15,16,17,18,19,22 are used by PCI devices Shared IRQs: IRQ 16 is shared by 4 PCI Devices IRQ 17 is shared by 2 PCI Devices IRQ 18 is shared by 2 PCI Devices IRQ 19 is shared by 4 PCI Devices IRQ control is currently managed by the system APIC controller - IRQ info is not actual hardware settings...